Synaccess Networks NP-0201DT User Manual
Autoping & power reboot, Power outlet manual switch (if equipped), Snmp and trap (s series)
AUTOPING & POWER REBOOT
Each power outlet can be configured to run Autoping
and reboot. Please use the web interface to
complete the settings.
POWER OUTLET MANUAL
SWITCH (IF EQUIPPED)
Press the “Power Outlet Manual Switch” button
located on the front panel. Keep press and release the
button until desired outlet LED is blinking. THEN
HOLD THE SWITCH DOWN FOR 3 SECONDS.
The selected outlet will change the On/Off state.
Note: a user reserved power outlet can’t be manually
controlled.
SNMP AND TRAP (S SERIES)
By default, SNMP agent and TRAP are disabled.
Default community string is “public”. To obtain a
copy of SNMP MIB files, open the device web page.
Down load the MIB file by clicking “get mib file” at
Network Setting” web page.
SAVE/LOAD SETTINGS
Saving and reloading system configuration data file is
done by running a small utility program on a PC. This
operation requires network connection.
Download “synCfg.exe” by visiting
Run the program at DOS prompt: “syncfg.exe –h”
FIRMWARE UPGRADING
The system is firmware upgradable via network.
Please contact us or visit our web site for upgrading
instructions and firmware version information.
PROGRAMMING INTERFACING
The unit can be easily managed by using direct TCP or
serial port interfacing.
Using Telent Port: default port # is 23.
Format: CmdCode Arg1 Arg2
Using HTTP/HTTPS. Note: HTTPS for S version.
http://my_IP_addr/cmd.cgi?cmdCode Arg1 Arg2
Command List
Command
Code
Arg 1
Arg 2
Login
$A1
ID
PWD
Logout
$A2
Set Outlet to
ON/OFF
$A3
Port#
V (1-ON;
0-OFF)
Reboot
$A4
Port#
Get Outlet
Status
$A5
Status Return
$A5
xxxx,cccc,cccc,tt
Or xxxx,cccc,tt
Each “x” denotes an outlet
state (“1” denotes ON; “0”
for OFF). The most right
“x” for relay1. “c” denotes
AC current draw (amp) and
“t” for temperature (c).
Set All Outlet
ON/OFF
$A7
V (1-ON; 0-
OFF)
Return Code
$A0
(OK)
Return Code
$AF
(Failed)
Unknown
Code
$AF
At serial or Telnet terminal, type command
“help” or “?” to get a list of commands.
Synaccess Networks, Inc
QUICK STARTUP
REFERENCE
For netBooter™ series T or B Part # 1090 V10
How to start:
1) Use a straight-thru Ethernet cable connect
the unit to your network:
By default, DHCP is disabled. The static IP
address is 192.168.1.100. Use a WEB or Telnet
program to configure the unit. The default
ID/Password is admin/admin. If you need to enable
the DHCP, please read “DEFAULT SETTINGS”
section.
2) Use a crossover Ethernet cable to connect
to a PC directly:
The static IP address for the unit is 192.168.1.100.
Make sure your PC IP address is on the same
subnet. 192.168.1.x. Use WEB or Telnet program
to configure the unit.
3) Use a serial cable to connect the unit and a PC:
Run a Terminal Program on the PC to configure
the unit. The serial port settings are 9600-8-N-1.
Type command “help” or “?” to view a list of
command.
Synaccess Networks, Inc.
75 W. Baseline Rd. Suite 10
Gilbert, AZ 85233
(928) 257-1838 Fax-(760) 930-0550
www.synaccess-net.com
Page 1
Default IP: 192.168.1.100
DHCP is not enabled. To enable it, see Section
DEFAULT SETTINGS below.
Default serial port: 9600-8-N-1.
Using WEB browser to see more detailed system
configuration description.
For serial or Telnet interfacing, type command
“help” to see a list of commands.
Page 5
Page 6
Document Outline
- AutoPing & Power Reboot
- Each power outlet can be configured to run Autoping and reboot. Please use the web interface to complete the settings.
- Power Outlet Manual Switch (if equipped)
- SNMP and TRAP (S Series)
- Save/load settings
- Firmware Upgrading
- programming interfacing
- Default Settings
- User Privilege Levels
- Start Configuration
- Power Outlet Control
- Control via emails (S Series)
- AC current draw and temperature reading