Datalogic Scanning Single Ethernet Cradle Datalogic Memor User Manual

Datalogic Scanning Hardware

Advertising
background image


Datalogic Memor™ Single Ethernet Cradle

NOTE

Read this manual carefully before performing any type
of connection through the Datalogic Memor™ Single
Ethernet Cradle.
The user is responsible for any damages caused by
incorrect use of the equipment or by inobservance of the
indication supplied in this manual.

NOTE

Do not attempt to disassemble the Datalogic Memor™
Single Ethernet Cradle, as it does not contain parts that
can be repaired by the user. Any tampering will invalidate
the warranty.



The Datalogic Memor™ Single Ethernet Cradle paired with one Datalogic
Memor™ mobile computer builds a reading system for the collection,
decoding and transmission of barcoded data.

The communication between the mobile computer and host PC through
the Datalogic Memor™ Single Ethernet Cradle may occur also by using
the standard ActiveSync® connection.

Figure 1 – Datalogic Memor™ Single Ethernet Cradle

A) LED

Indicators

B)

Spare Battery Slot

C)

Mini USB Connector

D) RS232

Connector

E) Power

Jack

F)

Ethernet Port with LED indicators

G) Switch

Ethernet/USB


The Datalogic Memor™ Single Ethernet Cradle is a serial
communication adapter between the host computer and the Datalogic
Memor™ mobile computer. Power supply is required to be connected to
the Cradle only for ethernet communication.
Since the Datalogic Memor™ Single Ethernet Cradle also functions as a
battery charger, a power supply is required for battery recharging
operations, both for the mobile computer and spare battery pack
recharging. The spare battery pack recharging slot can supply a 1000
mAh as well as a 2000 mAh Battery pac.


822000820

By inserting the Datalogic Memor™ into the cradle, data can be
transmitted to the host and its battery begins charging if the power supply
is connected. In addition, a spare battery can be charged by inserting it
into the slot at the back of the Datalogic Memor™ Single Ethernet Cradle
as shown in the following figure.

Figure 2 – Datalogic Memor™ Single Ethernet Cradle Charging and

Communication


The LEDs positioned on the front part of the Datalogic Memor™
Ethernet Cradle (see figure below) indicate the cradle and spare
battery charger status:

Figure 3 - LED Indicators


Front LED indicators

LED STATUS

Red Constant

Spare battery charging*


Charger

Green

Constant

Spare battery charge
completed

Power

Green

it is constant when the
cradle is powered


*

During charging, the LED may turn off to indicate a temporary
suspension of charging.

Ethernet Connector LED Indicators

Solid Green

Link established

Flashing Green

Link activity

Ethernet
Green LED
(left)

Off

No link established

Off

10 Mb connection

Ethernet
Yellow LED
(right)

Solid Yellow

100 Mb connection (this model is not
available)


CONNECTIONS

CAUTION

Connections should always be made with power OFF!

USB CONNECTION


The Datalogic Memor™ Single Ethernet Cradle can be connected to the
host by means of any standard Mini USB cable.

Once the host has been turned on, insert the Datalogic Memor™
mobile computer into the cradle.

Figure 4 - USB Connection

A) Host

Computer

C) Datalogic Memor™ Single

Ethernet Cradle

B) Std Mini USB (i.e.

94A051016 CAB-421)

D) *Power Supply (only necessary

for battery charging)

* Recommended power supply: 94ACC1324 PG5-30P35 AC/DC

POWER SUPPLY EU/USA PLUG.

NOTE

Be sure that the switch is in the “USB” position.
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the cradle.

Spare battery

Charge Slot with

Spare Battery

Inserted

Data Transmission and

Mobile Computer Battery

Charging

Spare Battery

Charger LED

Power LED

A

B

C

D*

A

B

C

D

F

G

E

Advertising