Operating fireplace, Continued – Desa CGFP28NT User Manual

Page 18

Advertising
background image

18

103413

UNVENTED (VENT-FREE) NATURAL GAS FIREPLACE

CGFP28N and CGFP28NT

Figure 43 - Pilot

Thermocouple

Ignitor Electrode

Pilot Burner

IGNITOR

LIGHTING

INSTRUCTIONS

Figure 42 - Control Knob and Ignitor
Button Location

WARNING: You must oper-

ate this fireplace with the fire-
place screen in place. Make sure
fireplace screen is installed be-
fore running fireplace.

NOTICE: During initial operation
of new fireplace, burning logs
will give off a paper-burning
smell. Orange flame will also be
present. Open window to vent
smell. Operate fireplace on HI
position to burn off odor. This
will only last a few hours.

1.

STOP! Read the safety information
in second column.

2.

Make sure manual shutoff valve is
fully open.

3.

Turn control knob clockwise
to the OFF position.

4.

Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety in-
formation above. If you don’t smell
gas, go to the next step.

Ignitor Button

Control Knob

OPERATING
FIREPLACE

Continued

1.

Follow steps 1 through 5 under Light-
ing Instructions
, page 17.

2.

Depress control knob and light pilot
with match.

3.

Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow step 8 under Lighting Instruc-
tions
, page 17.

Variable Manually-Controlled
Model CGFP28N

A. This appliance has a pilot which must

be lighted by hand. When lighting the
pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all

around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.

WARNING: If you do not fol-

low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
injury or loss of life.

FOR YOUR SAFETY

READ BEFORE

LIGHTING

THERMOSTAT

CONTROL OPERATION

You can set the thermostat control knob
to any comfort level between HI and LO.
The thermostat will gradually modulate
the heat output and flame height from
higher to lower settings, or pilot, in order
to maintain the comfort level you select.
The ideal comfort setting will vary by
household depending upon the amount of
space to be heated, the output of the
central heating system, etc.

Note:

Selecting the HI setting will cause

the burner to remain on without modu-
lating down in most cases.

MANUAL LIGHTING

PROCEDURE

WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow
the gas supplier’s instructions.

• If you cannot reach your gas sup-

plier, call the fire department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.

D. Do not use this appliance if any part

has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been un-
der water.

5.

Slightly depress and turn control
knob counterclockwise

C-clockwise

to

the PILOT position. Press in control
knob for five (5) seconds (see Fig-
ure 42).

Note:

If running fireplace for first

time, there will be air in gas line. You
may need to press in control knob for
30 seconds or longer. This will allow
air to bleed from the gas system.
• If control knob does not pop out

when released, contact a qualified
service person or gas supplier for
repairs.

6.

Continue pressing control knob in.
Press and release ignitor button. This
will light pilot. The pilot is attached to
the front burner. If needed, keep press-
ing ignitor button until pilot lights.

Note:

If pilot does not stay lit, con-

tact a qualified service person or gas
supplier for repairs. Until repairs are
made, light pilot with match. To light
pilot with match, see Manual Light-
ing Procedure
, page 19.

7.

Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob.

Note:

If pilot goes out, repeat steps

3 through 7.

8.

Slightly depress and turn control
knob counterclockwise

to

the HIGH position. Both burners
should light. Set control knob to de-
sired heat setting.

Advertising
This manual is related to the following products: