Comtech EF Data KST-2000L - Manual (Page 71)

Satellite Terminal System Revision 2
Terminal Mode Commands MN/KST2000L.IOM
7.7 Miscellaneous Commands
Miscellaneous commands and responses for resetting the internal M&C processor and for
determining system configuration information.
M&C
Soft Reset Command <add/SRM_'cr' Restarts system while retaining current variables
M&C
Hard Reset Command <add/HRM_'cr' Restarts system and resets variables to factory-default
values
M&C
Firmware
Information Command
Response <add/MCFI_'cr'
>add/MCFI_'cr'
VER_xxx.yyy.zzz'cr'
FW/nnnnn-ddr'cr'
Mm/dd/yy'cr''lf'] Where xxx.yyy.zzz = version number, nnnnn = firmware
number, dd = dash number, r = revision (- or A to Z)
Upconverter
Firmware
Information Command
Response <add/UFI_'cr'
>add/UFI_'cr''lf']
VER_xxx.yyy.zzz'cr'
FW/nnnnn-ddr'cr'
Mm/dd/yy'cr''lf'] Where xxx.yyy.zzz = version number, nnnnn = firmware
number, dd = dash number, r = revision (- or A to Z)
Downconverter
Firmware
Information Command
Response <add/DFI_'cr'
>add/DFI_'cr''lf']
VER_xxx.yyy.zzz'cr'
FW/nnnnn-ddr'cr'
Mm/dd/yy'cr''lf'] Where xxx.yyy.zzz = version number, nnnnn = firmware
number, dd = dash number, r = revision (- or A to Z)
HPA
Firmware
Information Command
Response <add/HFI_'cr'
>add/HFI_'cr''lf']
VER_xxx.yyy.zzz'cr'
FW/nnnnn-ddr'cr'
Mm/dd/yy'cr''lf'] Where xxx.yyy.zzz = version number, nnnnn = firmware
number, dd = dash number, r = revision (- or A to Z)
Query
Serial Numbers Command
Response <add/SNUM_'cr'
>add/SNUM_'cr'
UC_xxxxxxxxx'cr'
HPA_xxxxxxxxx'cr'
DC_xxxxxxxxx'cr'
M&C_xxxxxxxxx'cr''lf'] Where xxxxxxxxx – Serial Number ( 0 to 999999999)
Query
Assembly
Numbers Command
Response <add/ANUM_'cr'
>add/ANUM_'cr'
UC_nnnn-dr'cr'
HPA_nnnn-dr'cr'
DC_nnnn-dr'cr'
M&C_nnnn-dr'cr''lf'] Where nnnn = Assembly Number (0 to 9999), d = dash
number (0 to 9), r = revision (- or A to Z)
System
Maintenance
Status
Command
Response <add/MS_'cr'
>add/MS_'cr'
UCT_nn'cr'
HPT_nn'cr'
DCT_nn'cr'
MCT_nn'cr'
PRF_YY'cr'
FTD_xxx'cr'
HV_xxx'cr''lf'] Where nn = temperature in degrees C, YY =HPA RF
power value, xxx with FTD = OK, DLY or N/A for
TWTA heaters, xxx with HV = ON, OFF or N/A for
TWTA high voltage
Equipment
Type
Command
Response <add/ET_'cr'
>add/ET_tttttttt_xxx.yyy.zzz'cr''lf'] Where tttttttt = equipment type, xxx.yyy.zzz = firmware
version
Terminal
Emulation Command
Response
Status
Response <add/EMUL_xxxxxxxxxxxx'cr'
>add/EMUL_xxxxxxxxxxxx'cr''lf’'
<add/EMUL_'cr'
>add/EMUL_xxxxxxxxxxxx'cr''lf']
Where xxxxxxxxxxxx = RFT1200_2.06,
RFT1225_2.02/DISABLED which emulates the serial
remote command interface for the specified version of
the listed RFT product.
7–7