Denon DN-A7100 - Manual (Page 26)

22
ENGLISH
4 SURROUND
4 SURROUND
SURR.MODE :AUTO
HT-EQ :OFF
LFE LEVEL :
MAIN EXIT
1. Select “SURROUND” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2. To select a desired content , press the 3 or 4
cursor buttons.
SURR.MODE:
Select the desired surround mode with the 1 or 2
cursor buttons.
HT-EQ:
Select to active the HT-EQ with the 1 or 2 cursor
buttons.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is because
fi lm soundtracks were designed to be played back
in large movie theater environments.
Activating the HT-EQ feature when watching a fi lm
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
LFE LEVEL:
Select the output level of the LFE signal included in
the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the
1 or 2 cursor
buttons.
After you complete this portion of the set up, move
the cursor to “MAIN” with the
3 or 4 cursor buttons
and press the ENTER button.
3 PREFERENCE
3 PREFERENCE
STANDBY MODE : ECONOMY
TV-AUTO :
OSD INFO : ENABLE
BILINGUAL : MAIN
VIDEO CONVERT
HDMI : ENABLE
DC TRIGGER
MAIN
EXIT
1. Select “PREFERENCE” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2. To select a desired content, press the 3 or 4
cursor buttons.
STANDBY MODE:
When this function is set to “ECONOMY”, you can
reduce the power consumption when the unit is in
the standby mode.
Note:
TV-AUTO and RS-232C are disabled in the
“ECONOMY” setting.
TV AUTO:
Select the TV AUTO ON/OFF function to enable or
disable with the
1 or 2 cursor buttons.
OSD Info:
Select the OSD information function to enable or
disable with the
1 or 2 cursor buttons.
If you select “ENABLE”, the DN-A7100 will display
the status of the feature (Volume up/down, input
select, etc..) on the TV monitor. But if you do not
desire this information, select “DISABLE”.
BILINGUAL:
In the Bilingual mode, Dolby Digital and DTS
output is set to either “MAIN” or “SUB”. Select
“BILINGUAL” with the
1 and 2 cursor buttons,
then select MAIN ↔ SUB ↔ MAIN+SUB with the
1 or 2 cursor buttons.
VIDEO CONVERT:
Select the VIDEO CONVERT function to enable
or disable with the
1 or 2 cursor buttons. (Video
cable connection: Refer to page 15)
3-1 VIDEO CONVERT
TV : ON
DVD : ON
VCR1 : ON
DSS : ON
AUX1 : ON
MAIN RETURN EXIT
After you complete this portion of the set up, move
the cursor to “MAIN” with the
3 or 4 cursor buttons
and press the ENTER button.
HDMI AUDIO:
This setting determines whether to playback audio
input to the HDMI jacks through the DN-A7100 or
output it through the receiver to a TV or projector.
ENABLE: The audio input to the HDMI jacks
can be played back by this receiver.
In such case, audio signals are not
output to the TV or projector.
THROUGH: The audio input to the HDMI jacks is
not output from the output terminals
of the DN-A7100. Audio data is
output directly to the TV or projector.
This setting is used to listen to audio
on a multi channel TV, etc.
DC TRIGGER:
Select “DC TRIG SETUP” in the SETUP MAIN
MENU with
3 or 4 cursor button, and press the
ENTER button.
3-2 DC TIRGGER SETUP
DC TRIG DISABLE
TV : CD :
DVD : TAPE :
VCR1 : CD-R :
DSS : AUX2 :
AUX1 : TUNER:
7.1CH:
MAIN RETURN EXIT
You can select MAIN ROOM, REMOTE or DISABLE
by pressing
1 or 2 cursor buttons.
Notes:
• REMOTE is available for the external control. The
RC-1065 cannot operate this function.
• To select desired input source , press 3 or 4 cursor
button.
• To set ON or OFF, press 1 or 2 cursor button.
• After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor
buttons and press the ENTER button.