Denon DN-A7100 - Manual (Page 37)

33
ENGLISH
RECALLING A PRESET STATION
1.
1.
1.
(Using the DN-A7100)
1. Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front panel
(Using the remote control unit)
1. Press the PRESET – / + buttons to select the
desired preset station, or input your desired
preset channel with the numeric buttons on
the remote.
PRESET SCAN
1.
3.
3.
3.
(Using the remote control unit)
1. Press the P-SCAN on the remote.
“PRESET SCAN” appears on the display and
then the preset station with the lowest preset
number is recalled fi rst.
2. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
3. You can fast forward the preset stations by
pressing the PRESET –/+ continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CL button or P-SCAN on the remote.
MANUAL PRESET MEMORY
3.
2.
3. 2. 4.
(Using the DN-A7100)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3. Select the preset number by pressing the 1
or 2 cursor buttons, while this is still blinking
(approx. 5 seconds)
4. Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote control unit)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMO button on the remote. “– –“
(preset number) starts blinking on the display.
3. Enter the desired preset number by pressing
the numeric buttons.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
PRESET MEMORY
With this unit you can preset up to 50 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
2. 2. 5.
4. 1. 3.
1. To select FM, press the BAND button on the
front panel.
2. While pressing the MEMORY button, press the
2 cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3. Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4. If no button is pressed during this period, the
current station is memorized in location Preset
02.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5. Operation stops automatically when all 50
preset memory positions are fi lled or when auto
scanning attains the highest end of all bands.
If you desire to stop the auto preset memory at
anytime, press the CLEAR button.
(FM) TUNING MODE (AUTO STEREO OR MONO)
When in the auto stereo mode, AUTO indicator will
be illuminated on the display.
The “ST” indicator is illuminated when a stereo
broadcast is tuned in.
At open frequencies, the noise is muted and the
“TUNED” and “ST” indicators are not illuminated.
If the signal is weak, it may be diffi cult to tune into
the station in stereo. In such a case, press the
T-MODE button on the front panel or remote.
“AUTO” indicator is not illuminated, if FM stereo
broadcasts are received in monaural and the “ST”
indicator is not illuminated.
To return to auto stereo mode, press the T-MODE
button or press T-MODE button on the remote again.
AUTO indicator is illuminated on the display.