Digital Audio Labs Livemix System Quick Start Guide - Manual (Page 2)

WWW.DIGITALAUDIO.COM
LIVEMIX SYSTEM QUICK START
rev 1.1
1. The CS-DUO allows for 1/8” or 1/4” headphones,
or In-Ear Monitors. It can also be configured as
Balanced Mono for use with a powered floor
monitor.
2. To use 1/8” headphones, use the front panel
headphone jacks. To use with 1/4” headphones,
use the back panel 1/4” jack.
3. To use with floor monitors, the output settings
must be changed in the CS-DUO. This can be
done from the Mix Output Settings screen. See the
CS-DUO Users Guide for detailed information.
LIVEMIX DATA IN
24VDC 3.75A
LIVEMIX DATA OUT
STEREO MIXES 1-16
LIVEMIX DATA OUT MIX-16/32 STEREO MIXES 17-32 (MIX-32 ONLY)
12VDC 3.33A
LIVEMIX DATA OUT
AD-24
1 2 3 4 5 6 7 8
MIX-16
LIVEMIX
DATA AD-24
USB CS PORT FOOTSWITCH MIX A OUT MIX B OUT
LIVEMIX
DATA IN 24VDC 3.75A
LIVEMIX
DATA OUT STEREO MIXES 1-16
LIVEMIX DATA OUT MIX-16/32 STEREO MIXES 17-32 (MIX-32 ONLY)
PUSH TO SETUP MASTER OUT
PUSH TO SETUP ME & GROUP
PUSH TO SETUP MASTER OUT
PUSH TO SETUP ME & GROUP
PUSH TO SETUP MASTER OUT
PUSH TO SETUP ME & GROUP
PUSH TO SETUP MASTER OUT
PUSH TO SETUP ME & GROUP
PUSH TO SETUP MASTER OUT
PUSH TO SETUP ME & GROUP
PUSH TO SETUP MASTER OUT
PUSH TO SETUP ME & GROUP
PUSH TO SETUP MASTER OUT
PUSH TO SETUP ME & GROUP
PUSH TO SETUP MASTER OUT
PUSH TO SETUP ME & GROUP
SHIELDED
CAT5
GIGABIT NETWORK SWITCH
DANTE ENABLED MIXER/SNAKE/INTERFACE
CAT5/CAT6
CAT5/CAT6
LM-DANTE-EXP
Dante™ is a trademark of Audinate Pty Ltd.
DANTE NETWORK
LINK/ACT 1G
CAT5/CAT6
12VDC 3.33A
LIVEMIX DATA OUT
AD-24
ANALOG MIXER/SNAKE/INTERFACE
TRS CABLE
DB25 CABLE
(TASCAM PINOUT)
MIX A HEADPHONES AUX IN MIX B HEADPHONES
CS-DUO OUTPUT OPTIONS 5
CHANNEL NAMING 6
LOAD/SAVE GLOBAL
TEMPLATE
7
MIRRORMIX ® REMOTE MIXING 8
Livemix makes it easy to name each channel. It is
covered here as part of a quick setup and further in
the CS-DUO User Guide.
1. PRESS and HOLD on a channel cell on the
touchscreen to select a channel to edit.
2. PRESS and HOLD the top bar with the channel
number.
3. ENTER the channel name on the touchscreen.
4. PRESS Done or continue to the next channel
with the Next Channel button to the right of the
entry box.
5. The name will now show up on all the CS-DUOs
in the system.
Once the Livemix system is setup and channels
have been named, it is a good practice to Save
the Global Settings. The Global Templates
differ from the Saved Personal Mixes in that
Global Templates store only the Channel
Names, Channel Effect settings, and Global
information. Saving a Global Template allows
recall of band or team names and settings.
Saving a Global Template
1. PRESS Mix Tools on the touchscreen.
2. PRESS Global Setup.
3. PRESS Global Template Load/Save.
4. SELECT a location to save the template.
5. PRESS Save Selected Global Template.
6. PRESS Yes to confirm save.
7. ENTER Template Name.
8. PRESS Done.
Loading a Global Template
1. To Load a saved Global Template, follow
steps 1-3 above.
2. PRESS the slot of the Template you wish to
load.
3. PRESS Load Selected Global Template.
Some performers may need help with their
mix. With MirrorMix, any personal mixer can
control any other mixer while hearing what
the remote performer is hearing. You can also
Load a mix from the local unit onto the remote
unit. Please consult the CS-DUO User Guide
for detailed MirrorMix information.
To MIRRORMIX a remote CS-DUO
1. PRESS Mix Tools on the touchscreen.
2. PRESS MirrorMix.
3. SELECT the Port and Mix to MirrorMix. The
Port corresponds to the Ports on the MIX-
16/32 with A being the A mix and B being
the B mix.
4. The orange screens indicate you are mixing
a remote personal mixer.
5. PRESS the gray X at the bottom of the
Channel Overview screen to exit.
The 1/8” front panel and 1/4” back panel
connections are mirrored (in parallel). The system
can be set up for balanced mono or stereo
output, but not both at the same time.