Fusion MS-UD650 Installation - Manual (Page 3)

2 Connect the black wire to the negative (-) battery terminal.
3 Select an option:
• Connect the yellow wire to the positive (+) battery
terminal, and route the red signal wire
Â
to the ignition or
another manual switch
Ã
.
• Connect the yellow wire to the red, and connect them to
the positive (+) battery terminal.
Speaker Zones
You can group speakers in one area into speaker zones. You
can then control the audio level of the zones individually. For
example, you might want the audio quieter in the cabin and
louder on deck.
You can set the balance, volume limit, subwoofer level, and
name for each of the available zones. Up to two pairs of
speakers can be connected per zone in parallel to increase the
amplifier output.
Subwoofer Amplifier Connection Considerations
This stereo supports output to a powered subwoofer from all
zone outputs.
The subwoofer port on the stereo outputs a mono line-level
signal. The port output audio level is linked to the zone.
• You should connect the connectors to the included splitter.
• You need a splitter for each zone. One splitter is included.
Speaker Amplifier Connection Considerations
In addition to the two stereo speaker zones available through
the wiring harness, this stereo can be connected to multiple
amplifiers through zone connections.
• The blue wire from the wiring harness must be connected to
the amplifier to provide a signal to turn on the amplifier with
the stereo. If it is necessary to extend this blue signal wire,
use 22 AWG (0.33 mm²) wire.
• The audio output is a stereo line level output over standard
RCA cable.
Common Connections to the Stereo
You can connect a variety of additional media inputs and
outputs to the stereo, depending on the stereo model and the
devices to which you are connecting.
The connectors are color coded to assist you in making the
correct connections. For example, your TV may have an HDMI
connector. Connect the HDMI cable to the HDMI connector on
the stereo. This table lists some possible ways to connect
devices to the stereo.
NOTE: Not all connectors are available on all stereo models.
Input Stereo Connections
FM/AM radio antenna* Antenna connector
SiriusXM Connect Tuner ACCESSORY
USB device USB connector or the built-in dock (UD
models)
TV with a composite video
connector and RCA audio
line outs Yellow to COMPOSITE VIDEO
(MS-650AV only)
RCA line outs from TV to AUX IN 1 or
AUX IN 2
Input Stereo Connections
TV with component
connectors and RCA audio
line outs Three component video connectors to
matching connectors on stereo
(MS-650AV only)
RCA line outs from TV to AUX IN 1 or
AUX IN 2
TV with an HDMI connector HDMI (MS-750AV only)
* Metal hull vessels should use a marine, AM/FM, ground-
dependant antenna. Other vessels can use a marine, AM/FM,
ground-independent antenna.
Audio Return Channel
The Audio Return Channel (ARC) enables you to play the audio
from the television over the stereo system speakers.
ARC eliminates the need to connect a separate audio cable
from the HDMI television to the stereo. Typically, in televisions
without ARC, to play the audio from the television over the
stereo system speakers, you would need a separate cable. With
ARC, the HDMI cable sends the television audio to the stereo.
The HDMI version 1.4 cables support ARC. When planning your
stereo installation, check whether your devices support ARC.
Most devices that support ARC have an ARC label on the HDMI
connector that supports ARC.
NOTE: The Fusion MS-AV750 supports ARC.
Single-Zone System Wiring Diagram
À
Speakers
Á
Water-tight connection
Three-Zone System Wiring Diagram
À
Zone 1 speakers, powered from Class D amplifier in stereo
Á
Zone 2 speakers, powered from Class D amplifier in stereo
Â
Zone 3 line out, requires external amplifier
Ã
5-channel amplifier
3