Daewoo DCR-9120 - Manual (Page 27)

51
Recor
ding
50
NORMAL TIMER RECORDING
Timer Recordings Timer Recordings
TIMER RECORDINGS USING ShowView
■ For timer recordings, clock, date, and stations must be set correctly.
■ Load a cassette with its safety tab in place and with sufficient free space for the recording.
Call the ShowView menu by pressing PROGRAM on the
remote control.
From your TV magazine, type in the number next to the programme you
want to record ...
... and confirm.
1
Decide if you want to record "ONCE", "WEEKLY" or "DAILY"...
... and confirm.
2
If you wish to make changes:
Move to the position you want to change using the [œ/√] buttons.
Change the setting using the […/†] or [number] buttons. If all setting
are ok, press [ok], till you see “OK: CONFIRM” in the bottom line.
Confirm.
3
Switch your player off.
0-9:SHOWVIEW NUMBER
œ : CORRECT
OK:CONFIRM SETUP:END
SHOWVIEW
83077----
HOW OFTEN DO YOU WANT
TO RECORD THIS PROGRAM?
…/†:SELECT
OK:CONFIRM SETUP:END
TIMER PROGRAM (ONCE)
PR 03
START TIME 21:20
END TIME 22:20
START DATE 14/06(SAT)
TAPE SPEED SP
VPS/PDC ON
…/†:SELECT (AV1/AV2)
0-9 : SETUP (PR)
œ/√:CORRECT
OK:CONFIRM SETUP:END
ONCE
WEEKLY(ONCE A WEEK)
DAILY(MON-FRI)
DAILY(MON-SAT)
DAILY(MON-SUN)
• VPS/PDC is a service provided by some stations to enable you to perform timer recordings precisely even if
the broadcaster delays the start time of the programme slightly. The time you enter is the VPS/PDC time so
must be correct. Not all stations offer VPS/PDC, in which case the player will start at the time you enter and
not the actual start time of the programme.
If you wish to start recording at a specific time without it being adjusted by the VPS/PDC system in the
event of a delay, switch VPS/PDC off otherwise the player will not record.
• If you don’t have the ShowView numbers see next page for the normal timer.
• If you have made a mistake, move back to the relevant position with the [œ] button and change the setting.
• If there is no programme location displayed under “PR” in the change menu, the player doesn’t yet know
the location number for the programme you want. Type it in and this will be stored for last recordings.
• If you wish to record from a satellite receiver, select under “PR” the satellite programme location or AV (1/2)
(depending on the connection with the antenna cable or the SCART-cable). Leave the satellite tuner
switched on and to the programme you want.
• Should programming overlap, you get a warning.
• To cancel the recording press the
button (stop) more than 5 seconds.
• ShowView is a trademark applied for by Gemstar Development Corp.. The ShowView system is
manufactured under license from Gemstar Development Corporation.
■ For timer recordings, clock, date, and stations must be set correctly.
■ Load a cassette with its safety tab in place and with sufficient free space for the recording.
Call the player’s "SETUP", choose "TIMER PROGRAM".
Decide if you want to record "ONCE", "WEEKLY" or "DAILY"...
... and confirm.
1
Type in one after the other:
• The programme location number;
• the time the broadcast starts,
• the time the broadcast ends,
• the day of the broadcast, if it is not today.
• Select LP if you wish to make a very long recording .
• Switch off VPS/PDC here if you need to .
2
If you wish to make changes:
Move to the position you want to change using the [œ/√] buttons.
Change the setting using the […/†] or [number] buttons.
If all setting are ok, press [œ or √], till you see “OK : CONFIRM” in
the bottom line.
Confirm.
3
Switch your player off.
• Wait a few seconds after typing a one-digit-number.
• If you have made a mistake, move to the position you want to change using the [œ/√] buttons and
change the setting.
• If programme timings overlap, the machine will give a warning message. If you don’t adjust the times, the
machine will record the first programme completely then continue with the second one.
• If there is no sufficient free space for the recording on the cassette the video switches automatically to
“LP” for double recording capacity.
• The recorder will eject cassettes which have the safety tab removed.
…/†:SELECT (AV1/AV2)
0-9 :SETUP(PR)
œ/√: CORRECT SETUP:END
PR --
START TIME --:--
END TIME --:--
START DATE --/--
TAPE SPEED SP
VPS/PDC ON
TIMER PROGRAM (ONCE)
PR 01
START TIME 18:10
END TIME 20:30
START DATE 20/06(FRI)
TAPE SPEED LP
VPS/PDC ON
…/†:SELECT(AV1/AV2)
0-9 : SETUP (PR)
œ/√:CORRECT
OK:CONFIRM SETUP:END
TIMER PROGRAM (ONCE)
HOW OFTEN DO YOU WANT
TO RECORD THIS PROGRAM?
…/†:SELECT
OK:CONFIRM SETUP:END
ONCE
WEEKLY(ONCE A WEEK)
DAILY(MON-FRI)
DAILY(MON-SAT)
DAILY(MON-SUN)