Kleenmaid DCTBBQ - Manual (Page 7)

7
Timer function (barbecue/fryer)
This function simplifies cooking by allowing the cooking
cycle to continue without your presence. When you set
the timer, the heating element is automatically turned off
after the set time has elapsed. If the heating element is
set to 0, the timer just counts minutes (see the chapter
“using the timer to count minutes”).
Turning on the timer function (barbecue)
1 Select a power level between 1 and 12
2 Touch the timer button (9), the timer display (8) shows
“00” and the indicator light (7) turns on.
3 Select the cooking time in minutes (from 0 to 99)
using the “+” and “-” buttons (2). The timer function
will turn on in a few seconds and the indicator light (7)
starts flashing to indicate that the function is on. You
can quickly set the cooking time by holding down the
“+” or “-” button (2).
Turning on the timer function (fryer)
1 Select an oil temperature level between 80 °C and
200 °C.
2 Touch the timer button (9), the timer display (8) shows
“00” and the indicator light (7) turns on.
3 Select the cooking time in minutes (from 0 to 99)
using the “+” and “-” buttons (2). The timer function
will turn on in a few seconds and the indicator light (7)
starts flashing to indicate that the function is on. You
can quickly set the cooking time by holding down the
“+” or “-” button (2).
Fast turn-off of the heating element and timer
function (barbecue/fryer)
1 When you touch the “+” and “-” buttons (3) at the
same time, the heating element immediately turns off
and the timer function is cancelled.
Turning on the timer function to count minutes
(barbecue/fryer)
If the heating element is set to level 00, the timer can be
used to count minutes
Setting the timer to count minutes (barbecue)
If the appliance is off:
1 Touch the on/off button (1);
2 Touch the timer button (9);
3 Set the desired time using the “+” e “-” buttons (2)
If the appliance is on and the heating element is set to a
power level higher than 00:
1 Set the power to 00;
2 Touch the timer button (9);
3 Set the desired time using the “+” e “-” buttons (2)
Setting the timer to count minutes (barbecue)
If the appliance is off:
4 Touch the on/off key (1);
5 Touch the timer button (9);
6 Set the desired time using the “+” e “-” buttons (2)
If the appliance is on and the heating element is set to a
temperature level higher than 000:
4 Set the temperature to 000;
5 Touch the timer button (9);
6 Set the desired time using the “+” e “-” buttons (2)
Turning off the minute-counter function (barbecue/
fryer)
When the time has elapsed, a buzzer sounds for 2
minutes.
To cancel the buzzer early, just touch any button.
If you want to interrupt the timer before it runs down:
1 Touch the timer button (9)
2 Zero the time by holding down the “-” button (2)
Quickly turning off the minute-counter function
(barbecue/fryer)
Press the “+” and “-” buttons (2) at the same time.
Error messages
- AL0 (BARBECUE/FRYER) If a button is pressed for
more than 90 seconds, the buzzer will sound and AL0
will appear on the 3-digit display.
- AL1 (FRYER) If the probe has a short circuit, AL1 will
appear on the 3-digit display.
- AL2 (FRYER) If the probe is not connected, AL2 will
appear on the 3-digit display after it is on for about 5
minutes.
- AL3 (BARBECUE/FRYER) If the temperature of the
electronic board reaches 85°, AL3 will appear on the
3-digit display.