La Crosse Technology WS-9001U User Manual
Page 2
DISPLAY OF OUTDOOR TEMPERATURE READING
AND OUTDOOR MIN/MAX RECORDS:
1. Press the IN/OUT key to view the current outdoor
temperature
2. Press the MIN/MAX key to view the MIN record
3. Press again the MIN/MAX key to view the MAX
record.
4. Press the MIN/MAX once more to return to current
outdoor temperature.
OUT
IN
MAX
RX
TX
Receiver low
battery icon
Transmitter low
battery icon
Temperature
display in ˚F
Outdoor signal
reception icon*
OUT
IN
MAX
RX
TX
MIN
GB
P.6
GB
P.7
GB
P.8
GB
P.9
GB
P.10
GB
P.11
GB
P.12
GB
P.13
•
Shower proof casing
•
Wall mounting case
•
Mounting at a sheltered place. Avoid direct rain and
sunshine
SETTING UP
NOTE: The temperature station will receive one out-
door transmitter only.
1. First, insert the batteries into the Temperature
transmitter. (see “Install and replace batteries in
the Temperature transmitter”).
2. Immediately after and within 1 minute, insert the
batteries into Temperature station (see “Install and
replace batteries in the Temperature station”).
Once the batteries are in place, all segments of the
LCD will light up briefly. Then the indoor tempera-
ture will de display. If these are not displayed after
60 seconds, remove the batteries and wait for at
least 10 seconds before reinserting them.
3. After inserting the batteries into the transmitter, the
Temperature station will start receiving data from
the transmitter. The outdoor temperature and the
signal reception icon should then be displayed on
the Temperature station. If this does not happen
after 3 minutes, the batteries will need to be re-
moved from both units and reset from step 1.
4. In order to ensure sufficient 915 MHz transmission
however, this should under good conditions be a
distance no more than 330 feet (100 meters) be-
tween the final position of the Temperature Station
and the transmitter (see notes on “Mounting” and
“915 MHz Reception”).
INSTALL AND REPLACE BATTERIES IN THE
TEMPERATURE TRANSMITTER
The Temperature Transmitter uses 2 x AAA, IEC LR3,
1.5V battery. To install and replace the batteries, please
follow the steps below:
1. Pull out the battery holder at the bottom of the
transmitter.
2. Insert the batteries, observing the correct polarity
(see marking).
3. Replace the battery holder on the unit.
Note:
In the event of changing batteries in any of the units,
all units need to be reset by following the setting up
procedures. This is because a random security code is
assigned by the transmitter at start-up and this code
must be received and stored by the Weather station in
the first minute of power being supplied to it
INSTALL AND REPLACE BATTERIES IN THE TEM-
PERATURE STATION
The Temperature station uses 2 x AA, IEC LR6, 1.5V
batteries. To install and replace the batteries, please
follow the steps below:
SIZE AAA LR03
SIZE AAA LR03
1. Remove the cover at the back of the temperature
station.
2. Insert batteries observing the correct polarity (see
marking).
3. Replace compartment cover.
BATTERY CHANGE
It is recommended to replace the batteries in
all units on an annual basis to ensure optimum
accuracy of these units.
Please participate in the preservation of the
environment. Return used batteries to an
authorised depot.
F U N C T I O N K E Y S
Weather station:
The weather station has 2 easy to use function keys.
IN/OUT key
•
To toggle between the indoor and outdoor tempera-
ture display
MIN/ MAX key
•
To toggle between the current and MIN/MAX in-
door and outdoor temperature display
•
Press and hold to reset at the MIN/MAX indoor and
outdoor temperature records
LCD SCREEN AND SETTINGS
•
When the outdoor signal is successfully received
by the Temperature Station, this icon will be
switched on. (If not successful, the icon will not be
shown in LCD) So user can easily see whether the
last reception was successful (icon on) or not (icon
off).
DISPLAY OF INDOOR TEMPERATURE READING
AND INDOOR MIN/MAX RECORDS:
1. Press the IN/OUT key to view the current indoor
temperature
2. Press the MIN/MAX key to view the MIN record
3. Press again the MIN/MAX key to view the MAX
record.
4. Press the MIN/MAX once more to return to current
indoor temperature.
OUT
IN
MAX
RX
TX
MIN
OUT
IN
MAX
RX
TX
MIN
OUT
OUT
MAX
MIN
OUT
MAX
Indoor data
icon
Indoor
Temerature in
˚F
MIN icon
MAX icon
Outdoor data icon
Outdoor
Temperature in
˚F
MIN icon
MAX icon
in / out
min / max
IN/OUT key
MIN/MAX key