Marantz MCR603 - Manual (Page 39)

33
ENGLISH
Getting Started
Connections
Basic Operations
Advanced Operations Advanced Operations
Troubleshooting
Explanation terms
Information
Specifi
cations
Index
Firmware update
• In order to use these functions, you must have the correct system
requirements and settings for a broadband Internet connection
(vpage 8).
• Perform the fi rmware update operation after at least 2 minutes has
elapsed since turning this unit’s power ON.
1 Press [MENU] .
Turns on the Menu settings mode and the Menu appears on
the display. (vpage 26 “Menu map”)
2 Use ui to select “Other”-“Firmware Update”,
then press [ENTER/MEMO] , <ENTER> or p .
[Selectable items]
Check for Update : Check for fi rmware updates. You can also check
approximately how long it will take to complete
an update.
Start : Execute the update process.
• If updating fails, the set automatically retries, but if updating is still
not possible, one of the messages shown below is displayed. If
the display reads as shown below, check the settings and network
environment, then update again.
Display Description
Updating fail Updating failed.
Login failed Failure to log into server.
Server is busy Server is busy. Wait a while then try again.
Connection fail Failure in connecting to server.
Download fail Downloading of the fi rmware has failed.
[Notes concerning use of “Firmware Update”]
• Do not turn off the power until updating is completed.
• Even with a broadband connection to the Internet, approximately
20 minutes is required for the updating procedure to be completed.
• Once updating starts, normal operations on this unit cannot be
performed until updating is completed.
• Furthermore, updating the fi rmware may reset the backup data for
the parameters, etc. set for this unit.
• If the update fails, remove and re-insert the power cord. “Update
retry” appears on the display and update restarts from the point at
which update failed. If the error continues despite this, check the
network environment.
Setting speaker output
The speaker outputs of this unit are Speaker A, Speaker B, and
Bi-Amp. To switch these speaker output modes, use the “SPEAKER
SETUP” menu.
1 Press [MENU] .
Turns on the Menu settings mode and the Menu appears on the
display. (vpage 26 “Menu map”)
2 Use ui to select “Other”-“Speaker Setup”-“Speaker
Select”, then press [ENTER/MEMO] , <ENTER> or p .
3 Use ui to select Speaker output modes, then press
[ENTER/MEMO] , <ENTER> or p .
Speaker A
Speaker B
Bi-Amp
Outputs audio from the Speaker A output terminal.
(Default)
Outputs audio from the Speaker B output terminal.
Outputs the same audio from Speaker A output
terminal and Speaker B output terminal. The two
types of speaker connections are as follows:
• BI-AMP output
Outputs audio via one pair of speakers (vpage 33
“Listening to music using BI-AMP”).
• Speakers A and B output
Outputs audio via two pairs of speakers.
When you select “Bi-Amp” mode, the maximum output of the
amplifi er will be switched from 50W per channel to 25W per channel.
(8 Ω)
NOTE
Set the audio volume appropriately before making speaker setting.
n Listening to music using BI-AMP
Bi-amp can be used to connect speakers using two pairs of speaker
cables to connect the unit and speaker system.
Before making connections, check that the speaker system
supports bi-amp.
What is Bi-Amp?
Bi-amp is a technique used to improve sound quality where separate
speaker cables are used to connect to terminals for the low-end and
mid-range frequencies.
This connection method can help eliminate interference in the mid-
range caused by back-EMF generated by the speaker unit used for
the low-end.
NOTE
Be sure to set the same fi lter for both Speaker A and Speaker B when
listening to music on speakers connected using bi-amp. (“Setting
AMP characteristics” (vpage 34))
Connecting the speaker cables
Carefully check the left (L) and right (R) channels and + (red) and –
(black) polarities on the speakers being connected to the unit, and be
sure to connect the channels and polarities correctly.
R channel
speaker
L channel
speaker
NOTE
Be sure to remove the short plate connecting the LF and MF/HF
connectors on the speaker. Failure to do so may result in fi re and/or
damage to the equipment during use.
n Listening to music in two locations using a
multi-drive connection
You can listen to music in different rooms using this unit with two
pairs of speaker systems.
Setting the others [Other]
1.M-CR603N_ENG_0728.indd 33 1.M-CR603N_ENG_0728.indd 33 2010/07/29 20:39:28 2010/07/29 20:39:28