Vent-free propane compact fireplace, Operating fireplace, Continued – Desa CGCF26PRA User Manual

Page 16

Advertising
background image

16

105616

VENT-FREE PROPANE COMPACT FIREPLACE

OPERATING
FIREPLACE

Continued

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Fireplace

1.

Turn control knob clockwise
to the OFF position.

2a. Set selector switch in the OFF position.

2b.

If Using Optional Hand-Held Re-
mote:

Set selector switch in the OFF

position to prevent draining battery.

Shutting Off Burner Only (pilot
stays lit)

You may shut off the burner and keep the
pilot lit by doing one of the following:

1.

Turn control knob clockwise
to the PILOT position.

2.

Use remote control manual OFF button.

3.

Set selector switch in the OFF position.

1.

Follow steps 1 through 6 under Light-
ing Instructions
, page 15.

2.

Depress control knob and light pilot
with match.

3.

Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow steps 9 through 11, on page 15.

MANUAL LIGHTING

PROCEDURE

OPTIONAL REMOTE

OPERATION

Note:

All remote control accessories must

be purchased separately (see Accessories,
page 24). Follow installation instructions
on pages 14 of this manual.

Thermostat Control Operation

(Optional CGHRCT Series Only) The ther-
mostat control setting on the remote con-
trol unit can be set to any comfort level
between HI and LO. The burner will turn
on and off automatically to maintain the
comfort level you select. The ideal comfort
setting will vary by household depending
upon the amount of space to be heated, the
output of the central heating system, etc.

NOTICE: You must light the pilot
before using the hand-held re-
mote control unit. See

Lighting

Instructions on page 15.

1.

After lighting, let pilot flame burn for
about one minute. Turn control knob
to ON position. Adjust flame adjust-
ment knob anywhere between HI
and LO. Slide the selector switch to
the REMOTE position.

NOTE:

The

burner may light if hand-held remote
ON button was on when selector
switch was last turned off. You can
now turn the burner on and off with
the hand-held remote control unit.

IMPORTANT:

Do not leave the se-

lector switch in the REMOTE posi-
tion when the pilot is not lit. This will
drain the battery.

IMPORTANT:

Be sure to press the

ON/OFF buttons on the hand-held
remote control unit for up to 3 sec-
onds to assure proper operation.

CGHRC Series Operation:

2a. Press the ON/OFF button to turn the

burner on and off. When turning
burner off, the pilot will remain lit.

CGHRCT Series Operation:

2b. Select the MAN (manual) or AUTO

button on the hand-held remote con-
trol unit (see Figure 29, page 17).
• In manual mode, turn burner on

or off by pressing the ON or OFF
buttons on the hand-held remote
control unit.

Figure 28 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for
Remote Operation

O

FF

PIL

O

T

O

N

LO

IH

REMOTE
OFF
ON

Flame
Adjustment
Knob

Control Knob

Selector Switch in Remote
Position (Optional Remote Control)

• In auto mode, the room tempera-

ture is controlled by the thermo-
stat in the hand-held remote con-
trol unit. To increase the room tem-
perature, press the top arrow of the
TEMP button. To lower room the
temperature, press the bottom ar-
row of the TEMP button. At higher
settings the heater will run more.

IMPORTANT:

This remote control

has been specially engineered to take
an air temperature sample every 5.5
minutes in the AUTO mode. It will not
respond immediately to the tempera-
ture setting being turned up or down.

IMPORTANT:

The hand-held remote

control unit must be near the heater.
Do not keep the hand-held remote
control unit too close to the heater.
The thermostat on the hand-held re-
mote control unit will heat up too
quickly and turn the heater off.

3.

Use the STATUS button on the hand-
held remote control unit to see the
operation mode being used and the
temperature setting selected. A red
light will come on beside the opera-
tion mode being used when the sta-
tus button is pressed (see Figure 29,
page 17).

4.

To turn the burner off when operat-
ing in the manual mode, press the
OFF button. If operating in the auto
mode, press the MAN button, then
press the OFF button. The pilot will
remain lit (see Figure 29, page 17).

IMPORTANT:

To turn the pilot off,

manually turn the control knob on
the heater to the OFF position.

Advertising