Denon AVR-2310CI - Manual (Page 30)

2
ENGLISH
Get
ting Star
ted
Connections
Pla
ybac
k
Remot
e Contr
ol
Inf
or
mation
Tr
oubleshooting
Specifications
Multi-Zone
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
This is displayed after the Audyssey Auto Setup procedure is
completed.
Even if the settings are changed after the Audyssey Auto Setup
procedure, the Audyssey Auto Setup settings can be restored by
selecting “Restore” then pressing
.
1
Press ui to select
“Parameter Check”,
then press
p or .
2
Use ui to select the item you want to check, then
press p or .
Speaker Config. Check : Check the speaker configuration
Distance Check : Check the distance
Channel Level Check : Check the channel level
Crossover Freq. Check : Check the crossover frequency
EQ Check : Check the equalizer
3
Use o p to switch the display between the different
speakers.
4
Press .
The confirmation screen reappears. Repeat steps 2 and 3.
Check Audyssey Auto Setup
Measurement Results (Parameter Check)
A U T O S E T U P
P A R A M E T E R C H E C K
S p e a k e r C o n f i g C h e c k
D i s t a n c e C h e c k
C h a n n e l L e v e l C h e c k
C r o s s o v e r C h e c k
E Q C h e c k
R e s t o r e
S h o w s p e a k e r c o n f i g u r a t i o n r e s u l t
Error messages (examples) Cause Measures
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
N o m i c r o p h o n e o r S p e a k e r
R e t r y
R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Included setup microphone is not connected.
• Not all speakers could be detected.
• The front L speaker was not properly detected.
• Connect the included setup microphone to the
SETUP MIC jack on the main unit.
• Check the speaker connections.
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
A m b i e n t n o i s e i s t o o h i g h
o r L e v e l i s t o o l o w
R e t r y
R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Too much noise in the room for accurate
measurements to be made.
• Speaker or subwoofer sound is too low for
accurate measurements to be made.
• Either turn off any device generating noise or
move it away.
• Try again when the surroundings are quieter.
• Check the speaker installation and the direction
in which the speakers are facing.
• Adjust the subwoofer’s volume.
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
F r o n t R N o n e
R e t r y
E N T E R E n t e r R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Displayed speaker could not be detected.
· The front R speaker were not properly detected.
· Only one channel of the surround speakers was
detected.
· Sound was output from the R channel when only
one surround back speaker was connected.
· The surround back, but the surround speaker was
not detected.
• Check the connections of the displayed
speaker.
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
F r o n t L P h a s e
R e t r y
S k i p
E N T E R E n t e r R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Displayed speaker connected with the polarities
reversed.
• Check the polarities of the displayed speaker.
• For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure that the wiring is
correct, press
ui to select “Skip”, then press
.
NOTE Be sure to turn the power off before checking the speaker connections.
n To perform the Audyssey Auto Setup procedure again
Press ui to select “Retry”, then press .
n To cancel Audyssey Auto Setup
Press , the “Cancel auto setup?” prompt is displayed.
Press o p and select “�es”, then press .
Error Messages
If the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is
displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedure
over again.
Front
: Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menu
Remote control
operation buttons
:
Displaying the menu
Cancel the menu
Set
tings