Metro Basix Plus Electronic Locking - Manual

General Operating Instructions
Section 1: Unlocking the Cart for the First
Time
The cart comes pre-programmed with a Supervisor Code of
1234. This
is the only code that is programmed into the
cart at time of delivery . If a user wishes to open the cart
before programming any other codes , 1234 must be
entered. See Section 2 for detail on how to unlock and lock
the cart. Section 8 contains information on how to program
additional user codes.
Section 2: Unlock & Lock Cart
To Unlock the Cart:

Enter your 4-digit user or Supervisor code on the
touch pad .

Factory Default Supervisor code is 1234.

The green light will illuminate signaling a valid code
has been entered.

The cart drawers will now be unlocked.

NOTE : If the cart is already unlocked, the green
light will blink.
To Lock the Cart:

Push the Lock key on the touch pad.

NOTE: If the cart is already locked, the red light will
blink.
Section 3: Manually Lock& Unlock Cart
The cart ca n be unlocked manually (without the tou chpad
or electronics) by using the key lock . When this is done ,
the controlle r behaves exactly as if the user had entered a
user or Supervisor code to unlock the cart .

Insert the key into the mechanical key lock and turn
clockwise 90 degrees.

The cart will now be unlocked.

To lock the cart , turn the key 90 degrees counter
clockwise .

NOTE: If the cart is manually unlocked with the
key, it must also be re-Iocked using the key .
Section 4: Low Battery Indicator/Replace
Batteries
The red LED light will flash when batteries are at
approximately 20% of
remaining life.
To Change Batteries

Locate the battery storage box on the rear of the
cart .

Remove the screws holding the battery box cover in
place .

Remove the batteries and replace with (4) "D" size
alkaline batter i es (rechargeable batteries cannot be
used).

Replace cover and screws.
Programming Instructions
Section 5: Enter Programming Mode

Press <PRGM> Key

Red and Green LED lights will flash 4 times

Enter the 4 Digit Supervisor Code.
o Fa ctory Default Supervisor Code is 1234.
o To change the Supervisor Code , please see
Section 6 below.

Once the correct Supervisor Code is entered,
Green LED light will flash 3 times, prompting user
to select programming location.

Locations are listed below.

Incorrect Supervisor Code will result in the Red
LED light flashing once.

If this occurs, you must press <PRGM> Key and
re-enter Supervisor Code to begin programming.

NOTE: User must always wait for LED lights to
finish prompting before entering codes.
At this point , user can select from the following
programming locations :

000 - Supervisor Code

001 - 099 -- User Code

900 - Dual Mode

901 - Tamper Lockout Time

902 - Auto Lock Time - Minutes

903 - Auto Lock Time - Seconds

999 - Exit Programming Mode
Instructions for each programming location are detailed in
this document.
Section 6: Exit Programming Mode - 999

After all programming is complete, enter 999 to
exit programming mode.

Green and Red Lights will Flash 2 Times.

Normal cart mode is now resumed.
Section 7: Supervisor Code - 000
Change Supervisor Code

Follow steps to enter Programming Mode (See
Section 5).

Enter 000.

Green Light Will Flash 4 Times.

Enter New 4 Digit Combination (Valid
Supervisor code combinations are any
number from 0001 to 9999)

Green LED will flash once followed by a delay.

Green Light will then flash 3 times, prompting
user to enter next programming location or to exit
programming mode.

Move onto additional programming features by
entering the next desired 3 digit location.

Exit programming mode by entering 999 (See
Section 6 for more detail).
Electronic Locking
INSTRUCTIONS FOR USE
InterMetro Industries Corporation
North Washington Street, Wilkes-Barre, PA 18705
For Product Information Call: 1-800-992-1776
Visit Our Web Site: www.metro.com
Information and Specifications are subject to
change without notice. Please confirm at time of
order.