Metro Basix Plus Electronic Locking User Manual
Page 3
Disable Tamper Evident Lockout Time:
Follow steps to enter Programming Mode (See
Section 5).
Enter 901.
Green Light Will Flash 4 Times.
Enter 0000 Seconds to disable lockout time
Green Light Will Flash 1 Time followed by a slight
delay.
Green Light will then flash 3 times, prompting user
to enter next location or exit programming mode
(See Section 6 for more detail).
Section 11: Auto Lock Time
– 902(Minutes) or
903 (Seconds)
If the Auto
Lock
feature is
used
,
the lock
will energize after
the set amount of
time
has expired and the spring
tension
in
the
cabinet mechanism will cause the handle to
return to
the
locked
position.
The
factory default Auto
Lock Time
is set
to
a
minutes.
The
auto
lock time is
measured in minutes (i.e.
10 minutes =
010, 2 hours
= 120
minutes) for 902 or
seconds for 903.
Change Auto Lock Time:
Follow steps to enter Programming Mode (See
Section 5).
Enter 902 or 903.
Green Light Will Flash 3 Times.
Enter 001 - 999 Minutes (or seconds) to set desired
auto lock time.
Green Light Will Flash 1 Time followed by a slight
delay.
Green Light will then flash 3 times, prompting user
to enter next location or to exit programming mode
(See Section 6).
Disable Auto Lock Feature:
Follow steps to enter Programming Mode (See
Section 5).
Enter 902 or 903.
Green Light Will Flash 3 Times.
Enter 000 Minutes or Seconds to disable auto lock
feature Green Light Will Flash 1 Time followed by a
slight delay.
Green Light will then flash 3 times, prompting user
to enter next programming location or to exit
programming mode (See Section 6 for more detail).
Section 12: Reset Parameters to Default
Settings
It
is possible
to reset
all parameters back
to
default settings
.
The user
can set
all parameters
excluding
user
codes back
to factory defaults. Likewise, the user can set all
parameters
including user codes back to factory defaults
,
consequently
de
l
eting all existing user codes
.
In
order to delete all
user
codes and reset all programmed
features
back to factory
defaults
,
cart must be in programming mode
.
Reset Default Settings Excluding User Codes:
Remove top drawer from cart.
Locate control board on inside of front of cart
There is a small pushbutton located on the bottom
of the control board (orange in color).
Ensure cart is not in programming mode (See
Section 5 for more detail on programming mode).
Push the button.
All settings (excluding user codes) are now
returned to factory defaults, including the
Supervisor Code which will now be 1234.
Reset Default Settings Including All User Codes:
Remove top drawer from cart.
Locate control board on inside of face of cart
There is a small pushbutton located on the bottom
of the control board (orange in color).
Ensure cart is in programming mode (See Section
5 for more detail on programming mode).
Push the button.
All settings are now returned to factory defaults,
including the Supervisor Code which will now be
1234.
Replace drawer.
Cart is ready to be used or programmed.
NOTE: If cart is not in programming mode, all
settings will be set back to defaults but all user
codes will not be deleted.
Proximity Reader Operating Instructions
The
cart comes
pre-programmed
with a Supervisor Code
of 1234. This
is the only code
that
is programmed into the
cart at time of delivery.
If
a
user
wishes
to open the
cart
before programming
any
other
codes
,
1234 must be
entered
.
Likewise,
if the
user
wishes to
begin
programming proximity cards (stickers
,
key fobs
,
etc)
into
open user slots
,
the pre-programmed Supervisor code
must be used
to
enter
programming
mode
.
See
Section 5
for
more detail on programming mode. See Section
13
on
how to program
proximity
cards into
user
slots
.
Section 13: Program & Delete User
Proximity Cards - 001 - 099
There
are
99
User slots in addition to the 1 slot
reserved
for the Supervisor
.
The User
slots are numbered
001
through 099
.
Program User Cards:
Follow steps to enter Programming Mode (See
Section 5).
Enter 001.
Green light Will Flash 4 Times.
Swipe Proximity Card.
Green light Will Flash 1 Time followed by a slight
delay.
3