Operating fireplace, Continued, Manual lighting procedure – Desa (V)VC42N SERIES User Manual

Page 24: Optional hand-held remote operation, Shutting off burners only (pilot stays lit)

Advertising
background image

www.desatech.com

116236-01B

24

O

F

F

PILOT

LO

IH

O

N

Figure 45 - Control Valve

Piezo

Ignitor

Gas Control

Knob

Variable Control Knob

OPERATING FIREPLACE

Lighting Instructions (Cont.)
To Turn Off Gas To Appliance
Manual Lighting Procedure
Optional Hand-Held Remote Operation

OF

F

PIL

O

T

LO

IH

ON

OFF

REMOTE

ON

OFF

O

N

Blower Control Knob

(Optional Accessory)

Variable

Control Knob

Selector Switch

in Remote

Position

Gas Control Knob

in ON Position

Figure 46 - Setting the Selector Switch, Gas Control Knob and

Variable Control Knob for Remote Operation

OPERATING FIREPLACE

Continued

7. Turn gas control knob counterclockwise

to “PILOT”

(see Figure 45).

8. Push in gas control knob all the way and hold. Immediately

light the pilot by repeatedly depressing the piezo spark

ignitor until a flame appears. Continue to hold for about

one (1) minute after the pilot is lit. Release gas control knob

and it will pop back. Pilot should remain lit. If it goes out,

repeat steps 5 through 8.

• If gas control knob does not pop up when released, stop and

immediately call your service technician or gas supplier.

• If the pilot will not stay lit after several tries, turn the gas

control knob to “OFF” and call your service technician

or gas supplier.

9. Turn on all electric power to the fireplace.

10. Turn gas control knob counterclockwise

to “ON”.

11. This valve is equipped with a HI/LO feature. Set fireplace

input as desired.

12. Close lower louver panel.

TO TURN OFF GAS

TO APPLIANCE

1. Open lower louver panel.

2. Set selector switch in the OFF position to prevent draining

battery.

3. Turn off all electrical power to the appliance if service is to

be performed.

4. Push in gas control knob slightly and turn clockwise

to “OFF”.

5. Close lower louver panel.

Shutting Off Burners Only (pilot stays lit)

You may shut off the burners and keep the pilot lit by doing

one of the following:
1. Turn gas control knob clockwise

to the PILOT position.

2. Set selector switch in the OFF position.

MANUAL LIGHTING

PROCEDURE

1. Remove glass door (see Removing/Replacing Glass Door,

page 21).

2. Follow steps 1 through 8 under Lighting Instructions, page 23.
3. Depress gas control knob and light pilot with match.
4. Keep gas control knob pressed in for 30 seconds after light-

ing pilot. After 30 seconds, release gas control knob. Follow

steps 10 through 12 under Lighting Instructions,.

5. Replace glass door (see Removing/Replacing Glass Door,

page 21).

OPTIONAL HAND-HELD

REMOTE OPERATION

Note:

All remote control accessories must be purchased sepa-

rately (see Accessories, page 36). Follow instructions included

with the remote control.

NOTICE: You must light the pilot before using the

hand-held remote control unit. See

Lighting Instruc-

tions, page 23.

After lighting, let pilot flame burn for about one minute. Turn

control knob to ON position. Adjust flame adjustment knob

anywhere between HI and LO. Slide the selector switch to the

REMOTE position (see Figure 46). Note: The burner may light

if hand-held remote was on when selector switch was last turned

off. You can now turn the burner on and off with the hand-held

remote control unit.
IMPORTANT:

Do not leave the selector switch in the REMOTE

or ON position when the pilot is not lit. This will drain the

battery.

Advertising