Document Outline

• Chapter 1: Preliminary
  • 1.1 Limited Warranty
  • 1.2 Handling Instructions
• Chapter 2: Introduction
  • 2.1 Overview
    • 2.1.1 Timestamp Generator
    • 2.1.2 Board Reset
  • 2.2 Hardware Configuration
  • 2.3 Board Layout
  • 2.4 Cable Installation
• Chapter 3: Programming
  • 3.1 Thread Safety
    • 3.1.1 Atomic Read-Modify-Write
  • 3.2 Event-Driven Applications
  • 3.3 Error Codes
  • 3.4 Open/Close Functions
    • 3.4.1 S826_SystemOpen
    • 3.4.2 S826_SystemClose
  • 3.5 Status Functions
    • 3.5.1 S826_VersionRead
    • 3.5.2 S826_TimestampRead
• Chapter 4: Virtual Outputs
  • 4.1 Introduction
    • 4.1.1 Safemode
  • 4.2 Programming
    • 4.2.1 S826_VirtualWrite
    • 4.2.2 S826_VirtualRead
    • 4.2.3 S826_VirtualSafeWrite
    • 4.2.4 S826_VirtualSafeRead
    • 4.2.5 S826_VirtualSafeEnablesWrite
    • 4.2.6 S826_VirtualSafeEnablesRead
• Chapter 5: Analog Inputs
  • 5.1 Introduction
    • 5.1.1 Triggering
    • 5.1.2 Burst Counter
    • 5.1.3 Result Registers
  • 5.2 Connector J1
  • 5.3 Programming
    • 5.3.1 S826_AdcSlotConfigWrite
    • 5.3.2 S826_AdcSlotConfigRead
    • 5.3.3 S826_AdcSlotlistWrite
    • 5.3.4 S826_AdcSlotlistRead
    • 5.3.5 S826_AdcTrigModeWrite
    • 5.3.6 S826_AdcTrigModeRead
    • 5.3.7 S826_AdcEnableWrite
    • 5.3.8 S826_AdcEnableRead
    • 5.3.9 S826_AdcStatusRead
    • 5.3.10 S826_AdcRead
    • 5.3.11 S826_AdcWaitCancel
• Chapter 6: Analog Outputs
  • 6.1 Introduction
    • 6.1.1 Safemode
    • 6.1.2 Reset State
  • 6.2 Connector J1
  • 6.3 Programming
    • 6.3.1 S826_DacRangeWrite
    • 6.3.2 S826_DacDataWrite
    • 6.3.3 S826_DacRead
• Chapter 7: Counters
  • 7.1 Introduction
    • 7.1.1 ClkA, ClkB and IX Signals
    • 7.1.2 Quadrature Decoder
    • 7.1.3 ExtIn Signal
    • 7.1.4 ExtOut Signal
    • 7.1.5 Snapshots
    • 7.1.6 Preloading
    • 7.1.7 Tick Generator
    • 7.1.8 Cascading
    • 7.1.9 Status LEDs
    • 7.1.10 Reset State
  • 7.2 Connectors J4/J5
    • 7.2.1 Counter Signals
    • 7.2.2 Application Connections
  • 7.3 Programming
    • 7.3.1 S826_CounterSnapshotRead
    • 7.3.2 S826_CounterWaitCancel
    • 7.3.3 S826_CounterCompareWrite
    • 7.3.4 S826_CounterCompareRead
    • 7.3.5 S826_CounterSnapshot
    • 7.3.6 S826_CounterRead
    • 7.3.7 S826_CounterPreloadWrite
    • 7.3.8 S826_CounterPreloadRead
    • 7.3.9 S826_CounterPreload
    • 7.3.10 S826_CounterStateWrite
    • 7.3.11 S826_CounterStatusRead
    • 7.3.12 S826_CounterExtInRoutingWrite
    • 7.3.13 S826_CounterExtInRoutingRead
    • 7.3.14 S826_CounterSnapshotConfigWrite
    • 7.3.15 S826_CounterSnapshotConfigRead
    • 7.3.16 S826_CounterFilterWrite
    • 7.3.17 S826_CounterFilterRead
    • 7.3.18 S826_CounterModeWrite
    • 7.3.19 S826_CounterModeRead
    • 7.3.20 Common Applications
• Chapter 8: Digital I/O
  • 8.1 Introduction
    • 8.1.1 Signal Routing Matrix
    • 8.1.2 Safemode
    • 8.1.3 Edge Capture
    • 8.1.4 Pin Timing
      • 8.1.4.1 Noise Filter
    • 8.1.5 Reset State
  • 8.2 Connectors J2/J3
  • 8.3 Programming
    • 8.3.1 S826_DioOutputWrite
    • 8.3.2 S826_DioOutputRead
    • 8.3.3 S826_DioInputRead
    • 8.3.4 S826_DioSafeWrite
    • 8.3.5 S826_DioSafeRead
    • 8.3.6 S826_DioSafeEnablesWrite
    • 8.3.7 S826_DioSafeEnablesRead
    • 8.3.8 S826_DioCapEnablesWrite
    • 8.3.9 S826_DioCapEnablesRead
    • 8.3.10 S826_DioCapRead
    • 8.3.11 S826_DioWaitCancel
    • 8.3.12 S826_DioOutputSourceWrite
    • 8.3.13 S826_DioOutputSourceRead
    • 8.3.14 S826_DioFilterWrite
    • 8.3.15 S826_DioFilterRead
• Chapter 9: Watchdog Timer
  • 9.1 Introduction
    • 9.1.1 Operation
    • 9.1.2 Reset Out Circuit
    • 9.1.3 Initialization
  • 9.2 Connector P2
  • 9.3 Programming
    • 9.3.1 S826_WatchdogConfigWrite
    • 9.3.2 S826_WatchdogConfigRead
    • 9.3.3 S826_WatchdogEnableWrite
    • 9.3.4 S826_WatchdogEnableRead
    • 9.3.5 S826_WatchdogStatusRead
    • 9.3.6 S826_WatchdogKick
    • 9.3.7 S826_WatchdogEventWait
    • 9.3.8 S826_WatchdogWaitCancel
• Chapter 10: Safemode Controller
  • 10.1 Introduction
    • 10.1.1 Write Protection
  • 10.2 Programming
    • 10.2.1 S826_SafeControlWrite
    • 10.2.2 S826_SafeControlRead
    • 10.2.3 S826_SafeWrenWrite
    • 10.2.4 S826_SafeWrenRead
• Chapter 11: Specifications