Desa "A" Models - Manual (Page 21)

104415-01L
For more information, visit www.desatech.com For more information, visit www.desatech.com
21
21
OPERATING HEATER
Continued
Figure 32 - Setting the Selector Switch, Control Knob, and
Flame Adjustment Knob for Remote Operation
OPTIONAL HAND-HELD
REMOTE OPERATION
O
F F
PIL OT
O
N
LO
IH ON
OFF
REMOTE
Selector Toggle Switch (Optional
Hand-Held Remote Control)
Control Knob in
On Position
Flame Adjustment Knob
OPERATING HEATER (REMOTE-READY MODELS)
Optional Hand-Held Remote Operation
Note: All remote control accessories must be purchased sepa-
rately (see Accessories, page 36). Follow instructions included
with the remote control.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions on pages 19 and 20.
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjustment
knob anywhere between HI and LO. Slide the selector switch
to the REMOTE position (see Figure 32).
Note: The burner
may light if hand-held remote was on when selector switch
was last turned off. You can now turn the burner on and off
with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch in the RE-
MOTE or ON position when the pilot is not lit. This will
drain the battery.
THERMOSTAT SERIES (MODEL GHRCTB)
The hand-held remote can be operated using either the manual
mode (MANU) or thermostatic mode (AUTO) (see Figure 34).
To select Fahrenheit/Centigrade mode display, carefully press
the ˚C/˚F mode button with the end of a paper clip or similar
blunt object.
Manual Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press the MANU button to turn on the fireplace.
3. Press the POWER and LOCK buttons together to turn off
the fireplace.
Auto (Thermostatic) Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press AUTO button to select this mode.
3. Set the desired room temperature by pressing the TEMP
+ or - buttons.
4. Press the POWER and LOCK buttons together to turn off
the fireplace
Note: Do not leave the hand-held remote in the AUTO mode
close to the fireplace. The radiant heat from the fireplace will
turn off the fireplace. Ideally, place the hand-held remote in the
center of the room facing towards the fireplace.
Note: Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
ON/OFF SERIES (MODEL GHRCB)
Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 33).
TO LOCK press both buttons on hand-held remote control until
light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked
state, the light will not light up when any button is pressed.
TO UNLOCK press both buttons together on hand-held remote
control until the light stops flashing. The hand-held remote is
now unlocked.
Figure 33 - On/Off Hand-Held Remote Control Unit (GHRCB)
Control Button
Turns Burners
On and Off
Figure 34 - Thermostat Hand-Held Remote Control Unit (GHRCTB)
Turns Hand-Held
Remote On or Off
and Allows You to
Choose the Manual
Setting
Selects Auto
Setting
Increases Room
Temperature in
AUTO Mode
Locks System to
Prevent Accidental
Ignition
Digital Display
Shows
Temperature and
Settings
Turns Burners
On or Off
Decreases Room
Temperature in
AUTO Mode