Verilink S Lite (CG) Configuration/Installation Guide User Manual

S lite, Quick start guide, Specifications

Advertising
background image

Note: For more information about the S Lite,
see the reference manual, part number
34-00297, on the User Documentation CD or
at www.verilink.com.

Specifications

Interfaces

DCE:

DB-25, female

DTE:

DB-25, female

Performance Monitor

LED indicators:

Power, Loopback Active,
Tx Data, and Rx Data

Loopbacks

Remotely Initiated:

via standard V.54
commands

Locally Initiated:

via DIP switch

Configuration

Loopback Control:

1 position

Interface Control:

4 positions

Mechanical

Mounting:

desktop or wallmount

Dimensions:

1.25" H, 3.5" W, 5.75" D

Weight:

1 pound

Power Source

Input:

90–256 VAC,
autoranging

Output: 9

VDC

Industry Standards

Low Voltage Directive 73/23/EEC

EMC Directive

89/336/EEC

Environmental

Operating Temp:

0° to 50°C
(32° to 122°F)

Storage Temp:

20° to 70°C

(

4° to 158°F)

Humidity:

95% maximum
(non-condensing)

Wallmount Installation Using
Adhesive Strips

1 Select a place close to an AC outlet with

clearance for the signal and power cables.
The indicators and switches should be easily
accessible.

2 Verify the mounting surface is clean.

3 Cut the adhesive strip to the desired length

and affix the backing of one piece to the un-
derside of the unit.

4 Attach the other adhesive strip to the piece

on the underside of the unit.

5 Remove the backing to expose the sticky

surface.

6 Press the underside of the unit firmly against

the selected place.

Wallmount Installation
Using Screws

1 Select a place close to an AC outlet with

clearance for the signal and power cables.
The indicators and switches should be easily
accessible.

2 Vertically place two #6 screws 3-13

32

inches apart at the selected place. Leave the
screws out about an eighth of an inch.

3 Place the upright unit over the screws until

the holes engage and slide the unit down un-
til it locks.

Connections

DCE and DTE

Power

Plug the connector from the power supply into
the unit. Plug the transformer into an appropri-
ate outlet. This applies power to the unit.

Configuration

V.54 Annex B (RDL) Loop

Position 1 is used to set the unit to detect re-
motely initiated V.54 Annex B (RDL) loop
commands (A) or to manually initiate a loop-
back (B).

Interface

Positions 2, 3, 4, and 5 are used to select an in-
terface.

Note: Only one of these switches can be in
position B at a time.

Note: Disconnect the DCE and DTE cables
from the unit before selecting an interface.

Not Used

Positions 6, 7, and 8 are not used.

Indicators

The unit indicators show power loop status,
and data activity.

Power

This green indicator shows that power is
applied to the unit.

Loop Test

This indicator show the loop status of the unit.
Amber indicates the unit is in loop mode.
When the indicator is Off, the unit is not in
loopback.

Tx Data

This green indicator shows the unit is transmit-
ting data.

Rx Data

This green indicator shows the unit is receiving
data.

O
N

1 2 3 4 5 6 7 8

POWER

LOOP TEST

Tx DATA

Rx DATA

S Lite

D

T

E

D

C

E

POWER

B

A

S1

POSITION 1

POSITION 2

POSITION 3

POSITION 4

POSITION 5

POSITION 6-8

V.54 LOOP

X.21

EIA530

V.35

RS232

NOT USED

DETECT MODE

OFF

OFF

OFF

OFF

MANUAL LOOP

ON

ON

ON

ON

S1

A

B

FUNCTION

Pin DCE and DTE

Pin DCE and DTE

1

Shield Ground

14

TXD B

2

TXD A

15

TXC A

3

RXD A

16

RXD B

4

RTS A

17

RXC A

5

CTS A

18

LL

6

DSR A

19

RTS B

7

Signal Ground

20

DTR A

8

DCD A

21

RL

9

RXC B

22

DSR B

10

DCD B

23

DTR B

11

SCTE B

24

SCTE A

12

TXC B

25

TM

13

CTS B

2

3

1

4

B

A

V

.5

4

L

o

o

p

D

et

ec

t

X

.2

1

S

el

ec

te

d

n

o

t

se

le

ct

ed

n

o

t

se

le

ct

ed

E

IA

-5

3

0

S

e

le

ct

ed

5

8

6

7

n

o

t

se

le

c

te

d

R

S

-2

3

2

S

e

le

ct

ed

n

o

t

u

se

d

n

o

t

u

se

d

n

o

t

u

se

d

n

o

t

u

se

d

n

o

t

u

se

d

n

o

t

u

se

d

n

o

t

se

le

ct

e

d

V

.5

4

M

a

n

u

al

L

o

o

p

V

.3

5

S

el

ec

te

d

S1

45-00151

3.0

S Lite

Quick Start Guide

Advertising