Specifications — fox 500 da6, cont’d – Extron electronic FOX 500 DA6 User Manual
Page 2
Specifications — FOX 500 DA6, cont’d
Extron FOX 500 DA6 Fiber Optic Transmitter • Specifications
2
Sync
Input type ��������������������������������������� Autodetect RGBHV, RGBS, RGsB, RsGsBs
Input level �������������������������������������� 2�5 V to 5�0 Vp-p
Input impedance ��������������������������� 10k ohms
Polarity�������������������������������������������� Positive or negative (follows input or can be set by user)
Audio
Gain
Range ���������������������������������� Adjustable, -18 dB to +10 dB
Default
Captive screw connector
Unbalanced output: -6 dB; balanced output: 0 dB
Mini stereo jack ���������� Unbalanced output: 0 dB
Frequency response ���������������������� 20 Hz to 20 kHz, ±0�5 dB
THD + Noise ���������������������������������� 0�10% @ 1 kHz at nominal level
S/N �������������������������������������������������� >80 dB at maximum output (unweighted)
CMRR ���������������������������������������������� 65 dB @ 20 Hz to 20 kHz
Audio bits per sample ������������������ 18 bits per channel, 2 channels (L, R)
Sampling rate ��������������������������������� 48 kHz
Audio input
Number/signal type ��������������������� 2 inputs (mixed): 1 balanced stereo; 1 unbalanced stereo or 2 unbalanced
mono
Connectors ������������������������������������� (1) 3�5 mm captive screw connector, 5 pole
(1) 3�5 mm mini stereo jack
Impedance �������������������������������������� 18k ohms unbalanced, 20k ohms balanced, DC coupled
Nominal level �������������������������������� +4 dBu (1�23 Vrms), -10 dBV (316 mVrms)
Maximum level ������������������������������ +17 dBV, (unbalanced) at 1% THD+N
N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output— See FOX 500 Rx receiver specifications.
Control/remote
Serial control ports
Control �������������������������������� 1 RS-232, 3�5 mm captive screw connector, 5 pole (3 pins are used) (rear
panel)
1 RS-232, 2�5 mm mini stereo jack (front panel)
Pass-through ���������������������� 1 RS-232, 3�5 mm captive screw connector, 5 pole (3 pins are used) (rear
panel); in parallel with
1 RS-232, 2�5 mm mini stereo jack (front panel)
Baud rate and protocol
Control �������������������������������� 9600 baud, 8 data bits, 1 stop bit, no parity
Pass-through ���������������������� 9600 to 115,200 baud
Serial control pin configurations
Captive screw connectors: 1 = Tx, 2 = Rx, 3 = GND
Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND
Program control ����������������������������� Extron’s control/configuration program for Windows
®
Extron’s Simple Instruction Set (SIS
™
)
General
Power ���������������������������������������������� 100 VAC to 240 VAC, 50-60 Hz, 11 watts, internal
Temperature/humidity ���������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling ������������������������������������������� Convection, vents on top and side panels