Yaskawa AC SERVOMOTOR User Manual

Safety precautions, Warning mandatory caution, Caution mandatory caution prohibited

Advertising
background image

Checking Product

Verify that the ordered product as received by the model number marked on
the nameplate on the servomotor.
If any motor is incorrect or faulty, contact your Yaskawa representative or the
dealer from whom you purchased the products.

Note: Contents of the nameplate may differ in accordance with the series or

type of the motor.

Part Names

Note: Actual motor may vary in accordance with the series or type of the motor.

Checking on Delivery

Storage and Transportation

Installation

Wiring

Operation

Disposal

Regular Inspections

Daily inspection is sufficient for the maintenance of the motor.
The inspection and maintenance frequencies in the table are only guidelines.
Increase or decrease the frequency to suit the operating conditions and environ-
ment.

Part's Life Expectancy

The parts of the servomotors are subject to mechanical wear or deterioration over
time.
The life expectancy listed in the table is a reference period that may be affected by
the environmental and operating conditions.
If an unusual noise or vibration occurs, refer to the life expectancy table and con-
tact your Yaskawa representative. After examining the part in question, we will
determine whether the parts should be replaced or not. When the part has expired
before the expected time, further inspection will be required.

Free Warranty Period

This product is warranted for twelve months after being delivered to
Yaskawa’s customer or if applicable eighteen months from the date of ship-
ment from Yaskawa’s factory whichever comes first.

Scope of Warranty

If a Yaskawa product is found to be defective due to Yaskawa workmanship or
materials and the defect occurs during the warranty period, Yaskawa will pro-
vide a replacement, repair the defective product, and provide shipping to and
from the site free of charge.
However, if the Yaskawa Authorized Service Center determines that the prob-
lem with a Yaskawa product is not due to defects in Yaskawa’s workmanship
or materials, then the customer will be responsible for the cost of any neces-
sary repairs.

Before use

AC SERVO MOTOR

SGMAS-04ACA21

400

200

2.6

W

V

A

N

O

3000

B

1.27

min

Ins.

O/N 9271316-1

S/N DD9964567890012

YASKAWA ELECTRIC CORPORATION JAPAN

Serial number

Nameplate

-1

Order number

Servomotor model

Ratings

Encoder
connector

Servomotor
connector

Servomotor
main circuit cable

Flange

Encoder
cable

Nameplate

Encoder
(Detecting
section)

Output
shaft

Flange

Output
shaft

Nameplate

Encoder connector

Encoder
(Detecting
section)

Servomotor connector

General Precautions

The drawings presented in this instructions are sometimes shown without covers or

protective guards. Always replace the equipment's cover or protective guard as

specified first, and then operate the products in accordance with the instructions.

The drawings presented in this instructions are typical examples and may not match

the product you received.

These instructions are subject to change due to product improvement, specification

modification, and instructions improvement. When these instructions are revised,

the instructions code is updated and the new instructions is published as a next edi-

tion.

If the instructions must be ordered due to loss or damage, inform your nearest

Yaskawa representative or one of the offices listed on the back of this instructions.

Yaskawa will not take responsibility for the results of unauthorized modifications of

this product. Yaskawa shall not be liable for any damages or troubles resulting from

unauthorized modification.

Safety Information

The following conventions are used to indicate precautions in these instructions.

Failure to heed these precautions can result in serious or possibly even fatal injury

or damage to the products or to related equipment and systems.

Indicates precautions that, if not heeded, could possibly result in loss

of life or serious injury.
Indicates precautions that, if not heeded, could result in relatively

serious or minor injury, damage to the product, or faulty operation.
In some situations, the precautions indicated could have serious

consequences if not heeded.
Indicates prohibited actions that must not be performed. For exam-

ple, this symbol would be used to indicate that fire is prohibited as

follows:

Indicates compulsory actions that must be performed. For example,

this symbol would be used as follows to indicate that grounding is

compulsory:

Notes for Safe Operation

Ground the ground terminals of the SERVOPACK and the motor (or ground the

metallic part such as frame in case of no ground terminal) according to local and/or

national electrical codes (ground resistance: 100

Ω or less). Use grounding wires of

a size complying with relevant international or local standards.

Failure to observe this warning can result in electric shock.

Disconnect all power and wait 5 minutes before wiring or inspection.
Failure to observe this warning may result in electric shock by the residual voltage.

Do not damage the cables or subject them to excessive stress such as bending or

stretching. Do not place heavy objects on the cables or the cables between other

objects where they might be pinched.

Failure to observe this warning may result in electric shock, stopping operation of

the product, or burning.

The motor will become extremely hot during operation, so do not touch the motor

with bare hands.

Failure to observe this caution may result in burns.

Never touch the motor rotary parts during operation.
Failure to observe this warning may result in personal injury.

Installation, wiring, operation, maintenance and inspection must be performed only

by authorized personnel.

Failure to observe this warning may result in electric shock or injury.

If using the motor with the shaft key slot, do not touch the key slot with bare hands.
Failure to observe this caution may result in injury.

Do not disassemble or modify the product.
Failure to observe this warning may result in injury or damage to the product.

Do not come close to the machine immediately after resetting momentary power

loss to avoid an unexpected restart. Take appropriate measures to ensure safety

against an unexpected restart.

Failure to observe this warning may result in injury.

If connecting the motor to the machine, build an external emergency stop circuit that

immediately stops operation and shuts down power in an emergency.

Always use the servomotor and SERVOPACK in one of the specified combinations.
Failure to observe this caution may result in fire or malfunction.

WARNING

CAUTION

PROHIBITED

MANDATORY

WARNING

MANDATORY

CAUTION

Do not hold the product by the cables or motor shaft while transporting it.
Failure to observe this caution may result in injury or malfunction.

Do not place any load exceeding the limit specified on the packing box.
Failure to observe this caution may result in injury or malfunction.

If disinfectants or insecticides must be used to treat packing materials such as

wooden frames, pallets, or plywood, the packing materials must be treated before

the product is packaged, and methods other than fumigation must be used.

Example: Heat treatment, where materials are kiln-dried to a core temperature of

56

°C for 30 minutes or more.

If the electronic products, which include stand-alone products and products installed

in machines, are packed with fumigated wooden materials, the electrical compo-

nents may be greatly damaged by the gases or fumes resulting from the fumigation

process. In particular, disinfectants containing halogen, which includes chlorine, flu-

orine, bromine, or iodine can contribute to the erosion of the capacitors.

If the motor has been in storage for a long time, contact your Yaskawa representa-

tive.

Use the eyebolt of the motor only to transport the motor. Do not use it to transport

other machines.

For more information on storage environments, refer to Installation.

Do not store or install the product in the following places.
Failure to observe this caution may result in fire, electric shock, or damage to the

product.

• Outdoor locations or locations subject to direct sunlight.

• Locations subject to ambient temperatures outside the allowable temperature range.

• Locations subject to humidity levels outside the allowable humidity range.

• Locations at an altitude of 1000 m or more.

• Locations subject to condensation as the result of extreme changes in temperature.

• Locations subject to corrosive or flammable gases and near combustible sub-

stances.

• Locations subject to dust, salts, or iron dust.

• Locations subject to oil or chemicals.

• Locations subject to shock or vibration.

• Locations that are difficult to check, clean, and maintain.

Install the servomotor only in environments that meet the requirements for its pro-

tection class.

Failure to observe this caution may result in malfanction.

For applications where the motor may be splashed with large amounts of water or

oil, use a cover or take other protective action. Also, the connectors should face

downwards.

Do not step on or place a heavy object on the motor.
Failure to observe this caution may result in injury.

Be sure to prevent any foreign objects from entering the product.
Failure to observe this caution may result in malfunction or fire.

The motor shaft extension is coated with anticorrosive paint. Before installation,

wipe off the paint with a cloth soaked in liquid detergent.

If the extension is not wiped, the motor can not be connected with the machine.

For coupling with the load machine, use a flexible coupling for the servomotor being

used.

A flexible coupling with the high rigidity of the metallic-plate spring type is recom-

mended.

Lubricant agent differs in accordance with the frame numbers of the gear. If using oil

as a lubricant, always lubricate before operation.

The motor can be installed in either horizontal or vertical direction. However, when

using the models with an oil seal, installing the motor with the output shaft up may

cause oil to enter the motor depending on the operating conditions. Check the oper-

ating conditions. Mounting direction is limited for some motors with reduction gears.

For details, refer to the manual for each model.

The cable connector is secured on the top of the motor with screw (s) for some

models. Refer to the procedure for connecting the cable to the motor in the manual

for each model of motor.

If using a motor with a cooling fan, provide a space of 200 mm or more on the intake

side of the fan.

The motor system is precision equipment. Do not apply shock to the motor or the

motor output shaft. Design machines so that the thrust load and radial load applied

to the motor shaft extension during operation should be within the allowable range

described in the catalogue.

Do not block the air inlet and outlet, and do not let foreign materials enter.
Failure to observe this caution may result in fire.

Do not alter the motor in any way.

CAUTION

MANDATORY

CAUTION

PROHIBITED

Be sure to wire correctly and securely.

Failure to observe this caution may result in motor overrun and injury.

Securely connect the power supply terminal screws and motor output terminal

screws.

Failure to observe this caution may result in fire.

Always use the specified power supply voltage.

Failure to observe this caution may result in fire.

Make wiring length as short as possible. Separate power cables from signal lines at

least 30 cm (11.81 in.). Noise on signal lines may cause vibration or malfunctions.

Use YASKAWA-specified cables. To use other cables, check the rated current of

your equipment, and consider operating environment to select correct cables.

If cables not specified by YASKAWA are to be used for the encoder, select twisted-

pair shielded wires or multi-core, twisted-pair shielded wires.

The cable connector is secured on the top of the motor with one or more screws for

some models. For more details, refer to the manuals for the individual models.

If using a motor with a built-in thermostat, be sure to use the thermostat to help pre-

vent the motor from overheating.

If using a motor with a cooling fan, be sure to check the rotation of the fan after wir-

ing the cooling fan and before use.

Do not connect the commercial power supply with the motor.
Failure to observe this caution may result in fire or malfunction.

Perform test run as follows. Secure the motor and disconnect from load machine

system, check operations, then connect the motor to the load machine.

Failure to observe this caution may result in personal injury.

If an alarm is issued, correct the cause, verify safety, and reset the alarm.

Then, turn ON the power supply again and restart the servomotor.

Failure to observe this caution may result in personal injury.

Do not touch the SERVOPACK heatsinks, regenerative resistor, servomotor, or

peripheral devices while power is ON or soon after the power is turned OFF.

Failure to observe this caution may result in burns due to high temperatures.

Adjust the setting switches and the parameters of the servomotor before operation.

For setting details, refer to the related manual.

The holding brake is not a stopping device, and does not secure the load. Install a

stopping device on the load side to ensure load safety.

Failure to observe this caution may result in injury.

Keep away from the motor after momentary power loss, as it may unexpectedly

restart. Design a machine system to ensure the safety of the operators after restart

of the motor.

Do not use the holding brake of the servomotor for ordinary braking.
Failure to observe this caution may result in malfunction.

When disposing of the products, treat them as general industrial waste.

Inspection and Maintenance

Item

Frequency

Procedure

Comments

Vibration

and Noise

Daily

Touch and listen.

Vibration and noise must not

be greater than normal levels.

Exterior

According to

degree of

contamina-

tion

Clean with cloth or compressed

air.

Insulation

Resistance

Measure-

ment

At least

once a year

Disconnect the motor from the

SERVOPACK and test insulation

resistance at 500 V megger.

Must exceed 10 M

Ω. Measure

across the servomotor FG and

the phase-U, phase-V, or phase-

W power line.

Contact your Yaskawa repre-

sentative if the insulation re-

sistance is below 10 M

Ω .

Do not measure insulation re-

sistance or perform withstand

voltage test of the encoder.

Replacing

Oil Seal

At least

once every

5000 hours

Contact your Yaskawa represen-

tative.

Applies only to servomotors

with oil seals.

Overhaul

At least

once every

20,000

hours or 5

years

Contact your Yaskawa represen-

tative.

CAUTION

PROHIBITED

CAUTION

PROHIBITED

Part

Life Expectancy

Comments

Bearing

20,000 hours

Life depends on operation conditions. Check that there is

no unusual noise or vibration.

Warranty Information

SAFETY PRECAUTIONS

AC SERVOMOTOR

MANUAL NO. TOBP C230200 00B

Type

USA

-

SGM

-

SGM

-

To properly use the product, read this manual thoroughly and retain
for easy reference, inspection, and maintenance. Ensure the end user
receives this manual.

MANUAL NO. TOBP C230200 00B

12 -0

YASKAWA ELECTRIC CORPORATION

SAFETY PRECAUTIONS

AC SERVOMOTOR

IRUMA BUSINESS CENTER (SOLUTION CENTER)

480, Kamifujisawa, Iruma, Saitama, 358-8555, Japan
Phone 81-4-2962-5151 Fax 81-4-2962-6138
http://www.yaskawa.co.jp

YASKAWA AMERICA, INC.

2121, Norman Drive South, Waukegan, IL 60085, U.S.A.
Phone 1-800-YASKAWA (927-5292) or 1-847-887-7000 Fax 1-847-887-7310
http://www.yaskawa.com

YASKAWA ELÉTRICO DO BRASIL LTDA.

777, Avenida Piraporinha, Diadema, São Paulo, 09950-000, Brasil
Phone 55-11-3585-1100 Fax 55-11-3585-1187
http://www.yaskawa.com.br

YASKAWA EUROPE GmbH

185, Hauptstra

βe, Eschborn, 65760, Germany

Phone 49-6196-569-300 Fax 49-6196-569-398
http://www.yaskawa.eu.com

YASKAWA ELECTRIC KOREA CORPORATION

9F, Kyobo Securities Bldg. 26-4, Yeouido-dong, Yeongdeungpo-gu, Seoul, 150-737, Korea
Phone 82-2-784-7844 Fax 82-2-784-8495
http://www.yaskawa.co.kr

YASKAWA ELECTRIC (SINGAPORE) PTE. LTD.

151, Lorong Chuan, #04-02A, New Tech Park, 556741, Singapore
Phone 65-6282-3003 Fax 65-6289-3003
http://www.yaskawa.com.sg

YASKAWA ELECTRIC (THAILAND) CO., LTD.

252/125-126, 27th Floor, Muang Thai-Phatra Tower B, Rachadapisek Road, Huaykwang, Bangkok, 10310, Thailand
Phone 66-2693-2200 Fax 66-2693-4200
http://www.yaskawa.co.th

YASKAWA ELECTRIC (CHINA) CO., LTD.

22F, One Corporate Avenue, No.222, Hubin Road, Shanghai, 200021, China
Phone 86-21-5385-2200 Fax 86-21-5385-3299
http://www.yaskawa.com.cn

YASKAWA ELECTRIC (CHINA) CO., LTD. BEIJING OFFICE

Room 1011, Tower W3 Oriental Plaza, No.1, East Chang An Ave.,
Dong Cheng District, Beijing, 100738, China
Phone 86-10-8518-4086 Fax 86-10-8518-4082

YASKAWA ELECTRIC TAIWAN CORPORATION

9F, 16, Nanking E. Rd., Sec. 3, Taipei, 104, Taiwan
Phone 886-2-2502-5003 Fax 886-2-2505-1280

In the event that the end user of this product is to be the military and said product is to be employed in any weapons systems or the manufacture
thereof, the export will fall under the relevant regulations as stipulated in the Foreign Exchange and Foreign Trade Regulations. Therefore, be sure
to follow all procedures and submit all relevant documentation according to any and all rules, regulations and laws that may apply.

Specifications are subject to change without notice for ongoing product modifications and improvements.
© 2007-2014 YASKAWA ELECTRIC CORPORATION. All rights reserved.

Published in Japan October 2014 07-3
14-9-10

Advertising
This manual is related to the following products: