Document Outline

• 1.0 Introduction
  • Figure 1 Typical installation of OpenComms NIC card
  • 1.1 OpenComms Compatibility
    • Table 1 OpenComms availability
    • Table 2 Specifications
• 2.0 Installation
  • 2.1 Retrofit Kit
  • 2.2 Self-Contained Unit
    • Figure 2 Connections
  • 2.3 User Connections for OpenComms NIC
    • 2.3.1 Network Port
    • 2.3.2 BMS Port
    • 2.3.3 Configuration Port / Service Terminal
      • Accessing the Configuration Port
        • Figure 3 Null modem cable diagram
        • Figure 4 NIC main menu in HyperTerminal
• 3.0 System Configuration
  • 3.1 DIP Switch Settings
  • 3.2 Service Terminal
    • Table 3 Service terminal navigation
    • System Information Menu
    • Network Settings Menu
    • BOOTP and DHCP Mode
    • SNMP Communications Menu
    • Web Server
    • Telnet
    • Change User Name / Password
    • Firmware Updates Menu
    • Factory Settings Menu
    • Auxiliary Communications
• 4.0 Operation
  • 4.1 SNMP
  • 4.2 Liebert Global Products MIB
  • 4.3 RFC 1628 UPS MIB
    • 4.3.1 SNMP Traps
  • 4.4 MIB
  • 4.5 HTTP
  • 4.6 Modbus RTU
  • 4.7 System Reset
  • 4.8 Diagnostics
    • Figure 5 LED locations
• 5.0 Modbus Communications and Connectivity
  • 5.1 Implementation Basics
    • 5.1.1 Constraints
  • 5.2 Transmission Format
  • 5.3 Physical Connection
    • Figure 6 Typical maximum installation
    • Figure 7 Exceeding maximum specifications
  • 5.4 Modbus Slave Functions
    • 5.4.1 Data Type
    • 5.4.2 Function Code Support
    • 5.4.3 Read/Write Holding Registers (0x03, 0x06, 0x10)
    • 5.4.4 Read Input Registers (0x04)
    • 5.4.5 Read, Set Coil Status (0x01, 0x05, 0x0F)
    • 5.4.6 Read Input Status (0x02)
    • 5.4.7 Error Handling
      • Table 4 Exception response
      • Modbus Packet Formats
  • 5.5 RTU Framing Examples
    • 5.5.1 Read Registers (Function Code 0x03 & 0x04)
    • 5.5.2 Write single holding register (Function Code 0x06)
• 6.0 NIC Setup and Testing
  • 6.1 Jumper Placement
    • Figure 8 Jumper positions
  • 6.2 Testing the Network
  • 6.3 Service Terminal Troubleshooting
  • 6.4 SNMP Troubleshooting
  • 6.5 Web Troubleshooting
  • 6.6 Modbus Troubleshooting
• 7.0 Firmware Updates
  • 7.1 Establishing Communication-Necessary Components
  • 7.2 Establishing Communication-Service Terminal Settings
  • 7.3 Firmware Update Procedure
• 8.0 External Enclosures
  • 8.1 Power Connection
    • Figure 9 NIC-ENCL1 internal view
  • 8.2 Communication Connection
• 9.0 Retrofit Installation
  • 9.1 Environmental Installation
    • 9.1.1 Deluxe System/3
      • Figure 10 Deluxe System 3 NIC installation
      • Figure 11 Deluxe System 3 chilled water control cavity
      • Figure 12 ICS control cavity
      • Figure 13 Challenger installation location
  • 9.2 System Wiring (SM, AM, AG Microprocessors)
  • 9.3 Power Connection (SM, AM, AG Microprocessors)
    • 9.3.1 Power Connection (Level 0 and Level 10 Microprocessors)
    • 9.3.2 Communication Connection (SM, AM, AG Microprocessor)
    • 9.3.3 Communication Connection (Level 0 and Level 10 Microprocessors)
  • 9.4 Himod (LNA)
    • Figure 14 Himod NIC installation location
    • 9.4.1 System Wiring (Himod)
    • 9.4.2 Power Connection (Himod)
    • 9.4.3 Communication Connection (HiMod)
  • 9.5 Mini-Mate2
  • 9.6 Emerson Network Power (CEMS100 / LECS15)
  • 9.7 UPS Installation
  • 9.8 Npower
    • 9.8.1 Power Connection for NPower
    • 9.8.2 Communication Connection for NPower
      • Figure 15 NPower UPS NIC installation
  • 9.9 7200 UPS
    • Figure 16 7200 UPS NIC installation
  • 9.10 HiPulse UPS
    • Figure 17 HiPulse installation
  • 9.11 Static Switch2
    • Figure 18 STS2 typical NIC location
    • Figure 19 STS2 NIC installation, 800-1000A units
    • Figure 20 STS2 NIC installation, 100 - 600A units
  • 9.12 STS
  • 9.13 PDU and DataWave with PMP & EPMP