English, Français, Assemblage de l’aspirateur – Euro-Pro EP704 User Manual

Page 8: Utilisation, Réglage de la hauteur de la tête motorisée

Advertising
background image

English

3.

Changing the Filters:

A) This is best done every three months or depending on the amount

of usage.

B)

Remove the front panel of the vacuum cleaner.

C)

The post filter is facing the front of the unit on the bottom and the

pre-motor filter is located underneath the bag. To remove the post

motor filter, pull the locking tab on the right and it will snap out. To

remove the pre-motor filter, simply slide it out.

D)

To clean the filters rinse in warm, soapy water. Filters must

by completely dry before re-installing into your vacuum.

E)

Once filters have been replaced, replace front panel.

NOTE: DO NOT OPERATE VACUUM WITHOUT FILTERS IN

PLACE.

Français

Assemblage de l’aspirateur

Avertissement: Ne pas brancher l’aspirateur avant qu’il soit complètement

assemblé.

1.

Déballez toutes les pièces principales et mettre de

côté l’emballage.

2.

Mettre l’aspirateur en position verticale.

3.

Enlevez les deux vis (2) qui sont déjà fixées au

corps de l’aspirateur.

4.

De l’arrière de l’aspirateur, aligner le manche avec

les rainures et glisser sur l’aspirateur. Si

nécessaire, appuyez avec les pouces et les doigts

pour mettre le manche en place.

5.

Une fois que le manche est en place, fixez le

manche avec les deux vis (2).

Please Note:

If you are using the cloth bag, you should wash the

pre-motor filter in lukewarm water once or twice

a year. Make sure that the filter is completely dry

before you put it back into the vacuum cleaner.

Utilisation

L’aspirateur vertical a été conçu dans le but d’être utilisé, avec ses

outils, sur différents types de tapis et de moquettes, sur les meubles

couverts de tapisserie et sur les planchers nus. Lors de l’utilisation

des outils, maintenez le manche dans la position verticale.

Please Note:

The Cloth Bag is washable. It should however be replaced every three (3)

months to ensure peak performance of your vacuum.

1.

Ajustez la tête motorisée en fonction de
l’épaisseur du tapis, de la position basse
à haute.

2.

Insérez la fiche du cordon d’alimentation
dans une prise de courant.

3.

Appuyez sur le bouton de dégagement du
manche avec votre pied (voir illustration à
droite)

4.

Appuyez sur l’interrupteur marche/arrêt
pour mettre l’aspirateur en marche. Appuyez une deuxième fois pour
l’arrêter.

5.

Vous êtes maintenant prêts à passer l’aspirateur.

4.

Changing the Power Nozzle Belt:

A) Occasionally the power nozzle drive belt will require changing, the

frequency will depend upon the amount of use your vacuum sees.

B)

Turn unit “Off” and unplug from wall outlet.

C)

Use a Phillips screwdriver and remove the two screws from the

back of the motorized power head cover.

D)

Remove the two screws from the bottom of the motorized power

head.

E)

If the belt has broken, remove any loose pieces before replacing.

F)

Grasp the beater bar at either end and lift straight up.

G) Place one end of new belt over motor shaft and the other on the

round pulley end of the beater bar.

H)

Align the rubber supports at the ends of the beater bar, with the slots

in the motorized power head. Push into place. Ensure that the cut-

outs on the rubber supports face upwards.

I)

Replace the two screws from the bottom of the motorized power

head and then replace the cover. Then replace the two screws from

the back side of the motorized power head.

Réglage de la hauteur de la tête motorisée

AVERTISSEMENT: Pour éviter toute blessure, tenir les habits, les

cheveux, les doigts et tout autre partie du corps à l’écart des parties

mobiles (tel que le rouleau-brosse). Mettez l’interrupteur sur arrêt et

débranchez l’aspirateur avant de changer la hauteur.

A l’avant de l’aspirateur se trouve un bouton permettant de monter ou

de baisser la tête motorisée de l’aspirateur selon le type de tapis ou de

moquette. Après avoir débranché l ’aspirateur, mettez le bouton à la

position la plus basse pour un nettoyage maximum. Si l ’aspirateur est

difficile à pousser, choisissez une position plus haute, jusqu’à ce que

l ’aspirateur se déplace facilement. Il faut que le rouleau-brosse soit en

contact avec la moquette ou le tapis pour un nettoyage efficace.

18

5

Advertising