Sealey WL483D User Manual
Bench mounted work light 48 smd led, Wl483d, Fig.1 fig.2
1.1.
ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged
into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by
contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains
power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs for wear and damage and all electrical connections to
ensure that none is loose.
1.1.6. Important: Ensure that the product voltage matches the power supply to be used.
1.1.7.
DO NOT pull power plugs from sockets by the power cable.
1.1.8.
DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have repaired by
a qualified electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted.
In case of damage, remove and fit a new plug according to the following instructions (discard old
plug safely). (UK only - see diagram at right).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the green/yellow earth wire to the earth terminal ‘E’.
b) Connect the brown live wire to live terminal ‘L’.
c) Connect the blue neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that cable outer insulation extends beyond the cable restraint and that the restraint is tight.
Powerful 3 diopter 120mm precision lens gives high quality magnifying capabilities. Features 48 SMD LEDs to illuminate the object for
improved detailed work. Multi-position swing arm allows simple positioning of lamp to suit task. Features a G-clamp base to secure to a
workbench or table. Ideal for electrical engineers, engravers and fine detail work.
Original Language Version
WL483D Issue No.1 01/05/14
RECOMMENDED
FUSE RATING: 3AMP
Model No: .............................................WL483D
LEDs: .....................................................48 SMD
Supply:...................................................230V
© Jack Sealey Limited
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
4. OPERATION
fig.1
fig.2
INSTRUCTIONS FOR:
BENCH MOUNTED WORK LIGHT
48 SMD LED
MODEL NO:
WL483D
4.1. Mounting
4.1.1. Fix the clamp to a secure surface. See fig.1.
4.1.2. Lower the work light assembly into the clamp, use two
hands to prevent the lamp moving during this operation.
4.1.3. Turn on/off using the switch on top. See fig.2.
4.1.4. Adjust by loosening/tightening the head clamp. See
fig.3.
Note: Be aware of the effect of using the lamp close to a
window/door where it could be in direct sunlight.
Remember to close the lid on top whilst it is not in use.