Sealey 1100CXD User Manual
Trolley jack 2tonne with carry/ storage case, Fig.2 fig.1, Instructions for
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.
Use genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit working area. Keep working area clean and tidy and free from unrelated materials.
Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
Place wedges under wheels of vehicle, but ensure the jack wheels are free to move and that there are no obstructions.
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if automatic).
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
Ensure there are no passengers in the vehicle and that all non-essential persons keep a safe distance whilst the jack is in use.
Place jack under lifting points recommended by vehicle manufacturer (see vehicle hand book). Ensure lifting point is stable and centred on
saddle.
WARNING! When lifting at the jack's maximum rating (2tonne) or close to it, it is recommended that the effort of raising the load shall be
reduced by the use of assistance during this operation.
DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Use suitable capacity axle stands under the vehicle before proceeding with any task.
Ensure there are no persons or obstructions beneath the vehicle before lowering.
DO NOT operate the jack if damaged.
DO NOT work under the vehicle until axle stands have been correctly positioned.
DO NOT exceed the rated capacity of the jack and DO NOT adjust the safety overload valve.
DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
DO NOT allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only and use a qualified person to maintain jack hydraulic system.
DO NOT allow untrained persons to operate the jack and DO NOT use jack for purposes other than which it is designed.
When not in use store jack, fully lowered, in a safe, dry, childproof area.
Your new Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Important: READ ThEsE INsTRucTIONs cAREfully. NOTE ThE sAfE OPERATIONAl REQuIREMENTs, WARNINGs AND cAuTIONs.
usE ThIs JAck cORREcTly AND WITh cARE fOR ThE PuRPOsE fOR WhIch IT Is INTENDED. fAIluRE TO DO sO MAy cAusE DAMAGE
OR PERsONAl INJuRy AND WIll INvAlIDATE ThE WARRANTy. RETAIN ThEsE INsTRucTIONs fOR fuTuRE usE.
1. sAfETy PREcAuTIONs
2. AssEMBly & sPEcIfIcATIONs
3.1.
Before first use.
3.1.1. Before using jack for the first time, purge the hydraulic unit in order to eliminate any air in the system. Place handle (fig.2H) onto the
release valve (B) and open valve by turning the handle anti-clockwise, place handle back into the jacking point (A) and pump for 30 to
40 seconds. When complete, close the release valve by turning the valve (B) clockwise.
3.1.2. Place a few drops of hydraulic jack oil on pump piston and pump handle several times to distribute oil. Thoroughly lubricate moving
parts.
NOTE: If your model is supplied with a plastic carrying handle fit it over the frames central nuts. (See fig.1A)
3.2.
General jacking.
WARNING! Before lifting ensure section 1 safety instructions are read and understood.
WARNING! When lifting at the jack's maximum rating (2tonne) or close to it, it is recommended
that the effort of raising the load shall be reduced by the use of assistance during this operation.
3.2.1. Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which
the jack is to stand is level and solid (not tarmacadam).
3.2.2. Position the jack saddle under the vehicle manufacturer’s recommended lifting point.
3.3. Jacking the vehicle.
3.3.1. Place the handle onto the release valve (B) and turn it clockwise to close the valve. Place handle
into socket (A) and commence pumping handle up and down using maximum strokes until the jack
saddle reaches the vehicle jacking point. Check the jacking point is centrally located on the saddle and raise the vehicle.
3.3.2. Should the jack become overloaded, a safety excess pressure valve will open and stop the vehicle from lifting.
WARNING! The jack is a lifting device only and must not be used to support the load. Use correctly rated axle stands to support load.
3.4.
lowering the vehicle
3.4.1. If using axle stands, raise the jack high enough for the stands to be easily removed. Then place handle on release valve (B) and
turn anti-clockwise, very slowly, to open the valve.
3.4.2. The lowering speed is controlled by the amount you turn the handle. Lower carefully, avoid any sudden changes in descent rate which
may shock load the hydraulic system.
WARNING! Ensure there are no persons or obstacles beneath the vehicle, or in the path of its descent.
3. OPERATING INsTRucTIONs
fig.2
fig.1
Model: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1100cXD.v3
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Tonne
Min. saddle height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125mm
Max. saddle height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390mm
Max chassis height. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140mm
Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11.4kg
Carry case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . yes
Original Language Version
1100CXD.V3 (I) Issue: 3 - 06/03/14
INSTRUCTIONS FOR:
TROllEy JAck 2TONNE WITh cARRy/
sTORAGE cAsE
MODEL NO:
1100cXD.v3
© Jack Sealey Limited