Sealey MAC2300 User Manual
Heavy duty compressor 12v, Mac2300, Instructions for
InstructIons for:
Heavy Duty Compressor 12v
MoDEL no:
maC2300
1. saFety INstruCtIoNs
WarNING!
read operating instructions before use.
suitable for 12Volt operation only.
Do Not leave the unit unattended while in operation.
check capacity and maximum inflation pressure of inflatable
before commencing inflation.
Monitor the pressure gauge while in operation.
the gauge should be used as an indication of pressure only.
We recommend the use of a dial pressure gauge for definitive
reading.
Locate compressor on an appropriate surface for use.
WarNING! this compressor is capable of producing a high
pressure.
Do Not inflate any item beyond its maximum
capacity.
the 12volt cigarette lighter plug must not be substituted with
any other type of plug or electrical supply.
Do Not direct inflation hose connector head at yourself,
others or animals.
Do Not carry by the hose, or yank the hose from an inflation
valve.
Do Not pull the power cable from the vehicle accessory
socket by the power lead.
Do Not get the compressor wet or use in the rain.
Do Not use the compressor for a task it was not designed to
perform.
Do Not operate the compressor when you are tired, under
the influence of alcohol, drugs or intoxicating medication.
Do Not operate the compressor if any parts are missing as
this may cause failure or possible personal injury.
Do Not open the unit.
Keep children and non essential persons away from the
inflation area.
Keep the
compressor clean and in good condition.
replace or repair damaged parts. Use recommended parts
only. Non authorised parts may be dangerous and will
invalidate the warranty.
2. INtroDuCtIoN & speCIFICatIoN
3. operatIoN
IMPORTANT: pLease reaD tHese INstruCtIoNs CareFuLLy. Note tHe saFe operatIoNaL reQuIremeNts, WarNINGs aND CautIoNs. use tHIs
proDuCt CorreCtLy aND WItH Care For tHe purpose For WHICH It Is INteNDeD. FaILure to Do so may Cause DamaGe or persoNaL INJury,
aND WILL INvaLIDate tHe WarraNty. Keep tHese INstruCtIoNs For Future use.
WarNING! ensure you have read and understood the
safety instructions.
3.1. Place the compressor on a sound, flat surface ensuring that
the inflation air hose can reach the tyre valve.
3.2. Push the universal quick-connector fully onto the inflation valve
stem, and lock with the connector lever.
ImportaNt: Inflation will only be effective if the connector
head is fully fitted and locked onto the valve.
3.3. check the pressure gauge to determine the amount of
pressure already in the tyre. the gauge can be used without
switching the unit on. We recommend however the use of a
dial pressure gauge for a definitive reading.
3.4. check that the compressor on/off switch is in the off position
and plug the compressor into the vehicle accessory socket.
3.5. switch the compressor on. View the pressure gauge to
determine when the correct pressure has been achieved.
3.6. switch the compressor off to stop the supply of air.
3.7. unlock and remove the quick-connector from the inflation
valve, ensuring you do not lose any air in the process.
replace the dust cap onto the valve. When you have finished
using the compressor, disconnect it from the vehicle accessory
socket and store it in a safe, dry location.
3.8. General Information.
to inflate a completely flat tyre, there must not be any weight
on it. A vehicle must therefore be jacked up to take the weight
off of the tyre.
the time it will take to inflate a tyre will depend upon the
amount of air required.
should the compressor fail to start when switched on, check
that the vehicle accessory socket is working correctly.
Note: the compressor may also be used to inflate items
such as inflatable dinghies, sports balls, air beds etc. use the
appropriate inflation nozzle for the item.
CautIoN: Some items may not indicate pressure required or the
maximum pressure. Be careful not to over-inflate.
Note: the pressure gauge is not a calibrated instrument. It is
recommended to use an approved dial pressure gauge for a
definitive reading.
Housed in rugged composite case. suitable for inflating tyres
on cars, vans and 4x4s. Powered by a reliable, heavy-duty
motor. Integral gauge reads up to 20bar/300psi. supplied with
plug for use in vehicle accessory socket. Accessory kit,
containing Presta type adaptor, ball spike and two inflatables
adaptors included in storage compartment.
Maximum working pressure: 200psi.
Maximum pressure: 300psi.
Delivers 0.75cfm of air.
supplied with 4mtr power cord.
Air Hose length: 900mm.
environmental protection.
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycle centre and disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
ImportaNt: no liability is accepted for incorrect use of this product.
WarraNty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFormatIoN: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sole uK Distributor, sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
Original Language Version
MAc2300 Issue: 5 - 07/09/11