Sealey PC300 - Manual (Page 2)

 WARNING! Ensure you read, understand and apply Section 1
‘Safety Instructions’.
Reminder: DO NOT vacuum hazardous substances. Use of an
incorrect cartridge filter will invalidate your warranty.
4.1 ensure the machine is unplugged from the power supply. (fig.3.1)
4.2 remove the top section and fit the cartridge filter down over the
filter basket and push fully home. (fig.3.2)
4.3 reposition the head onto the drum body, and clip in place. (fig.3.3)
4.4 insert the larger end of the flexible hose into the front inlet on the
container and lock in place. Push the required extensions and nozzle
onto the flexible hose. (fig.3.4)
4.5 Plug in the power supply. (fig.3.5)
4.6 switch to the ‘on’ (position ‘i’). (fig.3.6)
4.7 When you have completed vacuuming, press the switch to ‘off’
2. cOnTenTS anD SpecIFIcaTIOnS
High powered, lightweight unit with blower facility. constructed from high
impact plastic, the drum unit is mounted on four castors. tool stowage
points on head and base. supplied with 4mtr cable with 3-pin plug, tool kit,
cartridge filter and wet-use foam filter.
2.1 carton content
2.1.1 carefully unpack the carton.
2.1.2 locate the two side clasps (fig.1.6) which hold the top section
(fig.1.3) in place.
2.1.3 undo the clasps, remove the top section and take out the items
in the container.
2.1.4 check and identify each component as listed below. if anything
is missing or damaged please contact your supplier immediately.
2.2 Specification
motor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V / 1400W
max. Vacuum Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140mbar
Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120m³/h
container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30ltr
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5kg
Vac Accessories Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35mm
Filter (see sect.9 ‘consumables’) - dry: . . . . . . . . . . . cartridge Filter
Filter (see sect.9 ‘consumables’) - Wet: . . . . . . . . . . . . . . . . . . .Foam
4. DrY vacuum cleanInG
3. aSSemBlY
3.1 ensure the mains plug is disconnected. (fig.2.1)
3.2 undo clasps. (fig.2.2)
3.3 lift off the top section assembly. (fig.2.3)
3.4 remove contents from inside the container. (fig.2.4)
3.5 turn the container upside down and insert the four feet with castors into
the slots and apply pressure to ensure they lock into place and secure
with the supplied screw. DO nOT overtighten screws. (fig.2.5)
3.6 For dry vacuum cleaning use the cartridge filter supplied. (fig.2.6)
3.7 For wet vacuum cleaning fit the supplied foam filter. (fig.2.7)
nOTe: Do not operate the cleaner without a cartridge filter fitted as this
will damage the machine and invalidate your warranty.
3.8 replace the top section onto the container. (fig.2.8)
3.9 Align up the top section with the clasps and snap into place, by applying
pressure at the mid point of the clasps. (fig.2.9)
3.10 Attach the noise diffuser (fig.1.17) to the blow connection. (fig.1.12)
3.11 insert the large end of the hose into the front inlet of the container and
lock in place by turning clockwise a quarter turn. (fig.2.10)
3.12 choose the desired extension tubes and nozzle and connect onto the
hose (fig.2.11).
Item Description Item Description
1 Handle 11 suction tube extensions
2 on/oFF switch 12 Blow connection
3 top section 13 combination nozzle
4 Filter basket 14 crevice nozzle
5 safety float valve 15 Foam filter
6 clasp 16 cartridge filter
7 container 17 noise diffuser muffler
8 Vacuum hose connection
9 drain Plug
10 Flexible vacuum hose
fig.3
fig.2
fig.1
1
9
7
6
2
17
3
12
8
5
15
10
16 11
14
13
16
4
Original Language Version Pc300 issue: 2 - 22/10/09