Fig.1, Maintenance – Sealey PSTART1000HD User Manual
Page 3
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. Edmunds, suffolk,
IP32 7AR
www.sealey.co.uk
5.7.
Observe the lEd status on the plug end of the HT leads. The green lEd should illuminate, if the red lEd illuminates cross-connection
has occurred. This must be remedied before moving to
5.8.
5.8.
With the Powerstart selector switch to ‘Off’ plug the leads into the socket situated beneath the switch.
Note: The connector will only fit the socket one way round, to prevent cross-connection.
5.9.
Turn the selector switch to select 12V or 24V to match the vehicle voltage.
5.10. make sure that no one is standing near the battery. When all criteria is met, start the engine.
5.11.
Once the vehicle has started, turn the selector switch to ‘Off’ and then disconnect the leads from the vehicle, see 5.12 for sequence.
IMPORTANT:
If the vehicle does not start within
FIVE seconds, DO NOT continue cranking. Let the Powerstart’s internal battery(ies) cool for FIFTEEN
minutes before attempting to start the vehicle again. Failure to do so may damage the unit.
5.12. To remove the lead clamps, firstly disconnect the BLACK (-) negative clamp followed by the RED (+) clamp.
5.13. After use, immediately recharge the Powerstart as described in 4.1.
WARNING! BEFORE CHARGING THIS UNIT, DISCONNECT THE OUTPUT HT LEADS FROM THE UNIT AS THEY WILL REMAIN
“LIVE” WHILE CHARGING.
WARNING! NEVER CLAMP THE OUTPUT HT LEADS TO THE CARRY HANDLE AS THIS COULD RESULT IN A SHORT CIRCUIT.
circuit Breaker
(manual reset)
circuit Breaker
(manual reset)
Test Button
selector switch
12V-OFF-24V
charger socket
(charger not shown)
HT leads
and socket
Battery condition
display
deep Flanges
(protect panel fascia)
fig.1
Red lEd
Green lEd
(see
5.7)
crocodile clamps
Red (+) Positive
Black (-) negative
6. MAINTENANCE
6.1.
The unit has no customer serviceable components. All repairs inside or outside the warranty period to be directed to your sealer dealer.
6.2.
Remove the HT leads plug and charger plug before cleaning the outer casing and all leads with a dry cloth. Replace the charger as
explained in section 4.
6.3.
store the HT leads and Powerstart indoors separately
.
Under the Waste Batteries and Accumulators Regulations 2009. Jack Sealey Ltd are required to inform purchasers of products
containing batteries (as defined with these regulations), that they are registered with Valpak's registered compliance scheme.
Jack Sealey Ltd's Batteries Producer Registration Number (BPRN) is BPRN00705.
PsTART1000Hd Issue: 2(sP) - 19/08/14
Original Language Version
© Jack sealey limited