Fig.9, Fuses – Sealey SUPERSTART520 User Manual
Page 4
5. Fuses
Your starter/charger is equipped with a safety fuse, or fuses, which will cut the power to the unit in the following circumstances:
a) overload - too high a current to the battery.
b) short circuit - clamps touch, or cross-connection to battery.
c) Prolonged starting attempts.
should the fuse blow take the following action:
5.1.
turn the unit off and disconnect from the mains power supply.
5.2.
Allow the unit to cool down, establish the reason for failure and correct.
5.3.
replace the fuse. use only sealey replacement fuses. Do not use a fuse with copper bridges or similar as these will damage your
equipment. refer to section 2 ‘specifications’ for fuse information and part numbers. We recommend you hold 2 or 3 spare fuses with
the starter/charger.
Note: the use of an incorrect fuse will invalidate your warranty.
4.7
startINg
WarNINg! DO NOt attempt to start engine with starter/charger if the battery is disconnected from the vehicle. the presence of the
battery is essential for the elimination of possible overvoltage that may be generated due to energy accumulating in the connection
cables at the starting stage.
4.7.1. check the vehicle manufacturer’s handbook and follow any special instructions. check that the battery is in good condition.
4.7.2. Ensure the starter/charger is disconnected from the mains power supply and, for models with dual voltage output, set the output
voltage to the same as the vehicle battery i.e. 12 or 24 volts.
4.7.3. check that the charger clamps and battery terminals are clean and free from oxidation.
4.7.4. Without removing the cables that connect the battery to the vehicle, connect the charger PosItIVE (red) lead to the PosItIVE (+)
terminal on the battery and the nEGAtIVE (black) lead to nEGAtIVE (-) terminal on the battery.
4.7.5.
starting will be greatly eased if the battery is given a short charge before the ignition switch is turned. this must always be
done with the selector switch set to the 'charge' position and NOt to 'starting'. Plug starter/charger into mains power supply
and perform a rapid charge for 5 to 10 seconds.
4.7.6. Move the starter/charger switch to the ‘starting’ position indicated by the symbol shown in fig.9. turn the vehicle ignition on and
crank the engine for a MAXIMuM of 3 seconds. If the vehicle does not start, wait 120 seconds and then
try again to a maximum of 5 cycles.
WarNINg! If the vehicle will not start, DO NOt continue as vehicle battery and electrical circuits may be
damaged, and the fuse in the charger will blow. Disconnect the charger and investigate for vehicle faults.
4.7.7. When the vehicle is running successfully, switch the starter/charger off, unplug from the mains power and
disconnect the power terminals from the battery.
fig.9
environmental protection.
recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed of in a manner which is compatible
with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way. contact your local solid waste
authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMpOrtaNt: no liability is accepted for incorrect use of this product.
WarraNtY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFOrMatION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sole uK Distributor, sealey group,
Kempson Way, suffolk Business Park
,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
Original Language Version
suPErstArt520.V5, suPErstArt620.V5 Issue: 2 - 16/03/10