Vitek VT-1262 PK - Manual (Page 6)

6
ENGLISH
experimentally• (always• start• with• the• lowest•
temperature•and•raise•it•gradually•until•you•get•
the•desired•result).
• Corduroy•and•other•fabrics•that•become•glossy•
quickly•should•be•ironed•strictly•in•one•direc-
tion• (in• the• direction• of• the• pile)• with• slight•
pressure.
• To•avoid•appearance•of•glossy•spots•on•syn-
thetic•and•silk•fabrics,•iron•them•backside.
SETTING THE IRONING TEMPERATURE
• Place•the•iron•on•its•base•(9).
• Insert•the•power•plug•into•the•mains•socket.
• Turn• the• knob• (11)• to• set• the• required• iron-
ing• temperature:• “•”,• “••”,• “•••”• or• “MAX”•
(depending• on• the• type• of• fabric),• the• pilot•
lamp•(8)•will•light•up.
• Once• the• temperature• of• the• soleplate• (14)•
reaches•the•set•point,•the•pilot•lamp•(8)•will•go•
out•and•you•can•start•ironing.
Note:
If you are ironing at high temperature but you
need to switch to low temperature, wait until the
soleplate temperature decreases and the pilot
lamp(8) lights up, and only then you may start
ironing. While steam ironing it is necessary to
set the ironing temperature “•••” or “MAX”.
The steam ironing sector is marked with corre-
sponding symbols on the temperature control
knob (11).
WATER SPRAY
• You• can• dampen• the• fabric• by• pressing• the•
water•spray•button•(5)•several•times.
• Make• sure• that• there• is• enough• water• in• the•
water•tank•(10).
DRY IRONING
• Place•the•iron•on•its•base•(9).
• Insert•the•power•plug•into•the•mains•socket.
• Set• the• continuous• steam• supply• knob• (3)• to•
the•position•
•(the•steam•supply•is•off).
• Turn• the• knob• (11)• to• set• the• required• iron-
ing• temperature:• “•”,• “••”,• “•••”• or• “MAX”•
(depending• on• the• type• of• fabric),• the• pilot•
lamp•(8)•will•light•up.
• Once•the•soleplate•(14)•reaches•the•set•tem-
perature,•the•pilot•lamp•(8)•will•go•out•and•you•
can•start•ironing.
• After• you• finish• ironing,• set• the• temperature•
control•knob•(11)•to•the•“MIN”•position.
• Pull•the•power•plug•out•of•the•mains•socket•and•
let•the•iron•cool•down•completely.
STEAM IRONING
While•steam•ironing•it•is•necessary•to•set•the•iron-
ing•temperature•“•••”•or•“MAX”.
The• iron• is• provided• with• an• anti-drip• valve• that•
stops•water•supply•if•the•iron•soleplate•tempera-
ture•is•too•low;•it•prevents•dripping•from•the•iron•
soleplate•openings•(14).•During•heating•and•cool-
ing•of•the•iron•soleplate,•you•will•hear•character-
istic•clicks•of•the•anti-drip•valve•opening/closing,•
which•indicates•its•normal•operation.
• Place•the•iron•on•its•base•(9).
• Set• the• continuous• steam• supply• knob• (3)• to•
the•position•
(the•steam•supply•is•off).
• Insert•the•power•plug•into•the•mains•socket.
• Make• sure• that• there• is• enough• water• in• the•
water•tank•(10).
• Turn•the•knob•(11)•to•set•the•required•ironing•
temperature:• “•••”• or• “MAX”,• the• pilot• lamp•
(8)•will•light•up.
• Once•the•soleplate•(14)•reaches•the•set•tem-
perature,•the•pilot•lamp•(8)•will•go•out•and•you•
can•start•ironing.
• Turn• the• continuous• steam• supply• knob• (3)•
to•set•the•steam•generation•rate,•steam•will•
start•going•out•from•the•soleplate•(14)•open-
ings.
• After• you• finish• ironing,• set• the• temperature•
control•knob•(11)•to•the•“MIN”•position,•and•the•
continuous•steam•supply•knob•(3)•to•the•posi-
tion•
•(steam•supply•is•off).
• Pull•the•power•plug•out•of•the•mains•socket•and•
let•the•iron•cool•down•completely.
• Open•the•water•inlet•lid•(2),•turn•over•the•iron•
and•drain•any•remaining•water.
ATTENTION!
If steam is not supplied constantly during the
operation, check whether the temperature control
knob (11) and the continuous steam supply knob
(3) are set properly and whether there is water in
the water tank (10).
BURST OF STEAM
The• burst• of• steam• function• is• useful• for• ironing•
folds• and• can• only• be• used• at• high• ironing• tem-
peratures•(when•the•iron•temperature•control•knob•
(11)•is•set•to•the•position•“•••”•or•“MAX”).
• When• pressing• the• burst• of• steam• button• (4)•
steam• will• go• out• of• the• iron• soleplate• more•
intensively.
Note:
To avoid water leakage from steam openings,
press the burst of steam button (4) with a 4-5 sec.
interval.
IM VT-1262.indd 6 10.06.2016 11:47:56