Powerfix Z29618-BS User Manual

Powerfix Lighting

Advertising

GB / IE

person responsible for their safety. Children
must never be allowed to play with the device.

This product is not a toy and should be kept
out of the reach of children. Children are not
aware of the dangers associated with han-
dling electrical products.

Do not use the article if you detect any kind
of damage.

CAUTION! DANGER OF
EXPLOSION! Do not operate
the LED work lamp in potentially

explosive environments in which there are
inflam mable vapours, gases or dusts.

The LED inspection lamp is protected against
water spray. However, the product, mains
adapter and car adapter must never be
immersed in water or other liquids. Failure to
observe this advice will create the risk of elec-

tric shock! Never hang the product near a
washbasin, pond and the like.

Connect the LED work lamp to a properly
installed mains socket or a suitable cigarette
lighter socket only. The voltages in each case
must comply with information given in the
section “Technical data”.

Ensure that the electrical socket is easily acces-
sible so that you can pull the plug quickly out
of the socket if necessary.

Do not carry out any modifications or repairs
to the product yourself. The LEDs cannot and
must not be replaced.

m CAUTION! The protective surround to the

LEDs cannot be replaced. Dispose of the LED
inspection lamp if you discover cracks or
signs of fracture on the protective surround.

Dispose of the product if the LED inspection
lamp, mains adapter or car adapter is dam-
aged.

Never connect the LED work lamp to a power
supply socket if the LED work lamp, power
lead or socket is damaged or the LED work
lamp has been dropped.

Ensure that the power lead cannot become
damaged by sharp edges or hot objects.
Unwind all the lead completely before use.

Keep easily flammable materials away the
product. Never hang objects above the LED
work lamp or the mains adapter and never
cover them.

Pull the mains adapter / plug out of the mains
socket / cigarette lighter socket when you are
not using the LED work lamp or before you
clean it. Do this as well if signs of a fault

develop during use or charging, e.g. smoke,
burning smell etc., or during a storm. When
doing this, pull directly on the mains adapt-
er / plug and not on the lead.

Protect the product against heat, cold, strong
vibrations and impacts.

CAUTION! LED RADIATION.
Avoid damage to eyes! Never
look directly at the LED. Never use

optical appliances such as magnifying glasses
or the like to look at the LED. Protect yourself
and your environment by taking proper pre-
cautions.

Never point the LED beam at reflective surfaces,
people or animals. This could result in blind-
ness or irritation of the eyes. Even weak LEDs
could result in eye damage.

Do not attach the hook

to hot objects. The

dead weight of the LED work lamp might
cause the hook to deform or bend out of shape.

Before use

Charging the LED inspection

lamp

Note: You can charge the LED inspection lamp
from an ordinary domestic mains power outlet or
from the cigarette lighter socket in your vehicle.

Tip: We recommend that you charge the LED

inspection lamp from an ordinary domestic mains
power outlet to avoid draining your vehicle’s
battery.
CAUTION! Do not connect the LED inspection
lamp to the cigarette lighter socket of your vehicle
if the vehicle battery is old or degraded. Failure

to observe this advice may result in your vehicle’s
engine not starting.
Note: To use the LED inspection lamp without an
adapter, you must first charge the integral recharge-
able batteries. It takes between 4 and 6 hours to
charge the integral batteries. The rechargeable
batteries are permanently installed in the handle
of the LED inspection lamp.
Note: Charge the LED inspection lamp for approx-
imately 12 hours before first use.
Note: Charge the LED inspection lamp at least
once a month, if it is to remain unused for an
extended period of time.
Note: If the LED inspection lamp has not been
charged for an extended period of time (approx.
2 months), you could find that the integral recharge-
able batteries have entered a dormant state.
Charge and discharge the LED inspection lamp a

number of times in succession to reactivate the
integral rechargeable batteries.

Switch off the LED inspection lamp during the
charging process (set the ON / OFF switch

to position

0).

Remove the rubber protection cap from the
bottom of the LED inspection lamp.

Insert the power output connection plug of
the mains adapter

or the car adapter

into the power input connection socket

the handle of the LED inspection lamp.

Note: During charging from a cigarette lighter
socket, ensure that the plug is always completely
inserted into the cigarette lighter socket of the
vehicle. Failure to observe this advice may
result in risk of fire from overheating.

Insert the mains adapter

into a mains

socket or the car adapter

into the ciga-

LED Work Lamp

Introduction

Familiarise yourself with the product

before using it for the first time. In addi-
tion please refer carefully to the operating

instructions below and the safety advice. Use the
product only as described and for the indicated
purpose. Keep these instructions in a safe place.
If you pass the product on to anyone else, please
ensure that you also pass on all the documentation.

Proper use

The product is intended for providing illumination
in dry indoor rooms and in outdoor environments.
If used outdoors the mains adapter must be pro-
tected from moisture and the weather. Any other

use or modification of the product constitute
improper use and pose a risk of short circuits, fire,
electric shocks and damage to the product. The
manufacturer is not liable for damage caused by
improper use. The product is not intended for
commercial use.

Description of parts and

features

Hook

Magnetic mount

Mains adapter

Car adapter (for cigarette lighter socket)

ON / OFF switch

Power input connection socket

Indicator LED

Technical data

Light bulb:

23 LEDs (white,
non-replaceable)

Light intensity :

approx. 12,000 mcd
(millicandela)

Lamp rechargeable
batteries:

3 x AA NiMH, 1000 mAh
(not replaceable)

Charging time:

approx. 4 to 6 hours

Burn time:

approx. 3 hours (with fully
charged battery)

Lifespan of LEDs:

approx. 20,000 hours

Protection class:
System of protection: IP44
Adapter:
Input:

230 V ~ 50 Hz

Output:

6 V , 300 mA

Model:

YX-0603

Protection class:
System of protection: IP20
Cigarette lighter:
Input:

12 V

Output:

12 V

, 240 mA

Scope of delivery

1 LED inspection lamp
1 Mains adapter
1 Car adapter for cigarette lighter socket
1 Magnetic mount
1 Operating instructions

Safety instructions

WARNING!

DANGER TO

LIFE AND RISK OF ACCIDENTS
FOR INFANTS AND CHILDREN!

Never leave children alone and unsupervised
with the packaging material. There is always
a risk of suffocation if children play with the
packaging material. Children often underesti-
mate risks. Always keep children away from
the packaging material. This product is not a
toy.

Children or persons who lack the knowledge
or experience to use the device or whose
physical, sensory or intellectual capacities
are limited must never be allowed to use the
device without supervision or instruction by a

Z29618-BS

LED WORK LAMP

Operation and Safety Notes

Advertising

Popular Brands

Popular manuals