Powerfix Z31280 - Manual (Page 6)

6
GB/
IE
The drill stand must be mounted on a w
o
rkbench or a stable
, tilt
-fr
ee table
, to
ensur
e a safe w
o
rk. Use the drill holes
5
in
the base plate
6
.
§
A
ssembl
y
Note
: Y
ou need a 5 mm he
xa
gon k
ey (
p
ro
vided
),
tw
o open-ended spanner
s (
10 mm & 14 mm
) and
a slot scr
ewdriv
er (
1
.2 x 8.0 mm
) for assembly and
adjustment.
Connect the pillar
7
to the base plate
6
.
Then fix the slider
9
on the pillar (
see F
ig. A
).
Mount the le
ver arm
2
onto the slider
(see F
ig. B
). T
ighten the scr
ew
s and nuts as
tight as possible. Mount the vice
13
onto the base plate. T
o
do
this connect the scr
ew
s with the guide slots
4
in the ba
se plate thr
ough the t
w
o long slots
14
(see F
ig. C
).
Note
: The vice can be positioned e
xactly b
y
mo
ving the guide slots and long slots.
§
Mount
ing t
he w
o
rk
-piece
Hold the quick
-release but
ton
16
pr
essed and
pull the locking de
vice
15
back as far a
s it
goes (
see F
ig. D
).
Place the w
o
rk
-piece into the vice
13
.
Pr
ess the quick
-release but
ton and push the
locking de
vice with the clamping jaw
17
against the w
o
rk
-piece.
Fix the w
o
rk
-piece with a right turn (
see F
ig. E
).
§
Clam
ping in and
ad
jus
ting t
he drill
Fit the drill with its clamping collar into the drill holding fixtur
e
3
and tighten secur
ely
(see F
ig. F
).
Inser
t a suitable drill bit into the chuck.
Unscr
ew
bolt
12
(see F
ig. G
).
Mo
ve
the slider
9
with the clamped in drill
on the pillar
7
, until the drill nearly touches
the w
o
rk
-piece.
Re
tighten scr
ew
secur
ely
.
§
Ad
jus
ting t
he drill dept
h
Loosen the block
8
and slide it up to the
slider
9
(
see F
ig. H
).
Loosen the locking scr
ew
10
b
y turning it to
the lef
t (
see F
ig. H
).
Mak
e sur
e that the bolt
1
will be r
eleased
doing this and slides do
wn to the lo
w
est
position. Mo
ve
the le
ver arm
2
do
wn and r
ead off
the desir
ed drill depth on the drill gauge with
indicator
11
.
Fix the locking scr
ew
10
and block
8
with a
right turn (
see F
ig. I
).
§
Ad
jus
ting t
he w
o
rk piece
Loosen the fixing scr
ew
s of the vice
13
.
Adjust the vice with the w
o
rk piece b
y sliding
it into position. Mark the e
xact position and punch a drilling
point on the w
o
rk
-piece. R
etighten the vice
(see F
ig. J
).
§
S
tor
a
g
e and care
Stor
e the he
xa
gon k
ey in the fixtur
e on the
slider
.
Stor
e the pr
oduct in a dr
y place
, out of the
re
ach of childr
en.
Clean the pr
oduct with a damp cloth.
Lightly gr
ease the mo
ving par
ts, rub the plain
metal par
ts with an oily cloth to pr
otect them
fr
om rust.
§
Dis
posal
The pack
a
ging is made fr
om
en
vir
onmentally friendly materials,
which may be disposed thr
ough y
our
local r
ec
ycling facilities.
Contact y
our local r
efuse disposal authorit
y for
mor
e details of ho
w to dispose of y
our w
o
rn-out
pr
oduct.
100714_14_DK_02.indb 6
29/4/14 5:43 am