KEPCO HSP Series Operator Manual User Manual
Kepco, Hsp series, Model
Advertising
Table of contents
Document Outline
- SECTION 1 - INTRODUCTION
- 1.1 Scope of Manual
- 1.2 General Description
- 1.3 Specifications
- TABLE 1-1. Model Parameters
- TABLE 1-2. General Specifications
- FIGURE 1-2. HSP (All), Nominal Mains Voltage: Temperature Derating,
- FIGURE 1-3. HSP 1500W, Low Mains Voltage: Temperature, Power Derating
- FIGURE 1-4. Outline Drawing
- 1.4 Miscellaneous Features
- 1.4.1 Control/Programming
- 1.4.2 Status Indicators/Flags
- 1.4.3 Setpoint Monitors:
- 1.4.4 Remote Error Sensing:
- 1.4.5 Load Sharing:
- 1.4.6 Load Monitor:
- 1.4.7 Auxiliary Supply:
- 1.4.8 Overcurrent/Undervoltage Protection:
- 1.4.9 Current Walk-in:
- 1.4.10 Remote Reset:
- 1.5 Options
- 1.5.1 Meters (M Suffix):
- 1.5.2 Battery Chargers (B Suffix):
- 1.5.3 Internal Blocking Diode (R Suffix):
- 1.6 Accessories
- TABLE 1-3. Accessories
- SECTION 2 - INSTALLATION
- 2.1 Unpacking and Inspection
- 2.2 Terminations and Controls
- FIGURE 2-1. HSP Series Front Panel Controls and Indicators
- FIGURE 2-2. Configuration Switch Functions
- FIGURE 2-3. HSP Series Rear Panel Connections
- TABLE 2-1. I/O Connector Pin Assignments
- 2.3 Source Power Requirements
- 2.4 Cooling
- 2.5 Preliminary Operational Check
- 2.6 Installation
- 2.7 Wiring Instructions
- 2.7.1 Safety Grounding
- 2.7.2 Source Power Connections
- 2.7.3 D-C Output Grounding
- 2.7.4 Power Supply/Load Interface
- 2.7.5 Load Connection - General
- 2.7.5.1 Load Connection - Method I (Local Error Sensing)
- FIGURE 2-4. Load Connection - Method I (Local Error Sensing)
- 2.7.5.2 Load Connection - Method II (Remote Error Sensing)
- FIGURE 2-5. Load Connection - Method II (Remote Error Sensing)
- 2.7.5.3 Load Connection - Method III (Series Connection)
- FIGURE 2-6. Load Connection - Method III - (Series Connection)
- 2.7.5.4 Load Connection - Method IV (Parallel Operation)
- FIGURE 2-7. Load Connection - Method IV (Parallel/Redundant Operation with Hot-Swap)
- 2.7.5.4.1 Redundancy and Hot Swap Applications
- 2.7.6 Load Sharing
- 2.7.7 Signal Connections
- 2.8 Mechanical Keying
- 2.9 Retaining Latches
- SECTION 3 - OPERATING INSTRUCTIONS
- 3.1 Operating Configuration
- 3.2 Remote Error Sense
- 3.3 Output Voltage Programming
- FIGURE 3-1. External Resistance Programming of Output Voltage
- FIGURE 3-2. External Voltage Programming of Output Voltage
- 3.4 Output Voltage Range
- 3.5 Current Limit Programming
- FIGURE 3-3. External Voltage Programming of Current Limit
- 3.6 Current Limit Programming Range
- 3.7 Setpoint Monitors
- 3.8 Overvoltage Protection Adjustment
- 3.9 Current Limit Characteristic
- 3.10 Current Walk-in Circuit
- FIGURE 3-4. Current Walk-in Characteristic
- 3.11 5VAUX Floating Supply
- 3.12 Remote Inhibit/Remote Reset Controls
- FIGURE 3-5. Remote Inhibit Control Operation
- 3.13 Module Current Monitor
- 3.14 Status Indicators and Status Flags
- TABLE 3-1. Status Indicators and Flags
- 3.14.1 Power Indicator/Source Power Status Flags
- FIGURE 3-6. Timing Diagram for POWER and DCFAIL Status
- 3.14.2 DCFAIL Indicator and Output Status Flags
- TABLE 3-2. Fault Detector Operation
- 3.14.3 OVERTEMP Indicator and Status Flags
- 3.14.4 FANFAIL Indicator and Status Flags
- 3.15 Front Panel Meter (M Option) Operation
- 3.15.1 Voltmeter Operation
- 3.15.2 Ammeter Operation
- 3.15.3 Parallel/redundant Operation
- 3.16 Battery (B Option) Operation
- TABLE 3-3. B Option Fault Detection Window
- FIGURE 3-7. HSP M (Meter) Option and B (Battery Charger) Option, Front Panel