Eiki EIP-1600T - Manual (Page 66)

62
Specifications
Projector
EIP-1600T
NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/
DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50
Single Chip Digital Micromirror Device
TM (DMD TM ) by Texas Instruments
Panel size: 0.65 ", 1chip DMD
Drive method: Digital Light Processing (DLP™)
No. of dots: 983,040 dots (1280 [H]
× 768 [V])
1–1.15 × zoom lens, F2.4–2.6, f = 19.0–21.9 mm
275 W DC lamp
RCA connector
Y: 1.0 Vp-p, sync negative, 75
Ω terminated
P
B
(C
B
): 0.7 Vp-p, 75 Ω terminated
P
R
(C
R
): 0.7 Vp-p, 75 Ω terminated
4-pin mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75
Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
15-pin mini D-sub connector
RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75
Ω terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
HDMI terminal (video signal only)
720 TV lines (DTV720P)
45–85 Hz
15–70 kHz
12–85 MHz
9-pin mini DIN connector
Power jack: DC 12V output
AC 100–240 V
3.7 A
50/60 Hz
355 W (Lamp Setting “Bright”)/
310 W (Lamp Setting “Eco + Quiet”) with AC 100 V
340 W (Lamp Setting “Bright”)/
300 W (Lamp Setting “Eco + Quiet”) with AC 240 V
4 W (AC 100 V) – 5 W (AC 240 V)*
1
1,335 BTU/hour (Lamp Setting “Bright”)/
1,165 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 100 V
1,280 BTU/hour (Lamp Setting “Bright”)/
1,130 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 240 V
41°F to 95°F (+5°C to +35°C)
–4°F to 140°F (–20°C to +60°C)
Plastic
38 kHz
12
13 /
32
" Ч 4 19 /
64
" Ч 11 1 /
32
" (315 (W) × 109 (H) × 280 (D) mm) (main body only)
12 13 /
32
" Ч 4 47 /
64
" Ч 11 37 /
64
" (315 (W) × 120 (H) × 294 (D) mm) (including adjust-
ment foot and projecting parts)
8.8 lbs. (4.0 kg)
Remote control, Power cord for U.S. and Canada, etc., Power cord for Europe,
except U.K., Video cable, DIN-D-sub RS-232C adaptor, Quick Guide, Owner’s
manual
Product type
Model
Video system
Display method
DMD panel
Lens
Projection lamp
Component input signal
(INPUT1/2)
S-video input signal
(INPUT 3)
Video input signal
(INPUT 4)
Computer RGB/
Component input signal
(INPUT 5)
HDMI input signal
(INPUT 6)
Horizontal resolution
Vertical frequency
Horizontal frequency
Pixel clock
RS-232C terminal
TRIGGER terminal
Rated voltage
Input current
Rated frequency
Power consumption
Power consumption (standby)
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Replacement parts
* 1 When STANDBY Mode is set to “Eco”
As a part of policy of continuous improvement, EIKI reserves the right to make design and
specification changes for product improvement without prior notice. The performance specifica-
tion figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.