Euro-Pro S3305H - Manual (Page 6)

FEATURES OPERATING INSTRUCTIONS
Your Steam Mop utilizes steam to remove tough grease,dirt and grime. Steam is
nature’s purest and most powerful cleaner for safely cleaning all hard floor surfaces in
your home without harsh chemicals, thus being perfectly ecological. Cleans your tile,
hardwood , linoleum and vinyl floors. How To Assemble & Use
6. Plug the unit into a standard 120 volt
grounded wall receptacle.
7. Press the On/Off button to turn the
unit on. The power ‘On” light will light
up. It takes the unit approximately
two - three (2-3) minutes to heat up.
8. When there is no more water in the
water tank, the empty light (red) will
go on.
9. To refill the water tank, turn the unit
off and unplug from the electrical wall
outlet and let the unit cool for 30
seconds. Then remove the filling cap
and pour in the water. You do not
have to wait for the unit to cool down
before you refill.
10. When you have finished using the
steam mop, turn the unit “Off” and
wait until the steam mop cools down
for approximately five (5) minutes
before removing the micro-fiber
cleaning cloth or bonnet (optional)
from the base. Please note that the
micro-fiber cleaning cloth or bonnet
(optional) gets very hot with the
steam.
11. Never leave the micro-fiber cleaning
cloth or bonnet (optional) on the unit
when you have finished using the
steam mop. Always remove the
micro-fiber cleaning cloth or bonnet
(optional) and wash in warm water
with a mild detergent. Never use
bleach or fabric softener when
cleaning the micro-fiber cleaning
cloths or bonnet (optional). The
micro-fiber cleaning cloth or bonnet
(optional) can be washed in a
washing machine and dried in a
clothes dryer but on a low heat
setting. We recommend that you air
dry for 24 hours.
CAUTION: Use a grounded receptacle. Use only a heavy duty extension
cord rated for 15 amps minimum - Do not use an ordinary
extension cord.
IMPORTANT: Do NOT add cleaning solutions, scented perfumes, oils or
any other chemicals to the water used in this appliance.
Use regular water or distilled/purified water if the tap
water in your area is very hard.
WARNING: Your Steam Mop is designed to clean hard floor surfaces that
will withstand high heat. Do not use on unsealed wood or
unglazed ceramic floors. On surfaces that have been treated
with wax or some no wax floors, the sheen may be removed by
the heat and steam action. It is always recommended to test an
isolated area of the surface to be cleaned before proceeding.
We also recommend that you check the use and care
instructions from the floor manufacturer. 1. Remove all the parts from the
packaging.
2. Insert the ergonomic handle into the
tube pivot of the main unit.
3. Place one of the micro fiber cleaning
cloths or bonnet (optional) on the
bottom of the steam mop. Make sure
that the micro-fiber cleaning cloth or
bonnet (optional) is firmly attached to
the bottom of the steam mop. (Fig. 1)
4. Place the steam mop on the floor
protector pad and open the filling
cap.
5. With the help of the filling flask, pour
1 cup of water (8 oz.) Into the unit. do
not overfill.. Replace filling cap when
finished. (Fig. 2)
IMPORTANT: Always insure that the
unit is “UNPLUGGED” from the wall
receptacle prior to initial filling and before
attaching the micro-fiber cleaning cloth to
the base of the appliance. Never use the
steam mop without the micro-fiber
cleaning cloth or bonnet (optional)
attached to the base.
Always let unit cool for at least 5 minutes
before removing the micro-fiber cleaning
cloth or before emptying the water tank.
IMPORTANT:
Never leave the appliance in one spot on any surface
for any period of time. Always place the appliance on the
floor protector pad and make sure that the appliance is
turned off.
Fig. 1
Fig. 2
WARNING: Colors may bleed
during first wash. Be careful when
machine washing or drying with
mixed fabrics as micro-fiber cloths
will pick up lint from other fabrics.
Using The Micro-Fiber
Bonnet
(Optional)
If you wish to use the micro-fiber bonnet
(optional), follow same instructions as
above, except that you slip the bonnet
(optional) over the main unit.
4 5