Emerson EWC19T4 - Manual (Page 31)

- 31 - EN
1C29
OTR (One Touch Recording) Push(es) Display Recording length
1 push (normal recording)
2 pushes 0:30 30 minutes
3 pushes 1:00 60 minutes
17 pushes 8:00 480 minutes
You can make copies of video tapes made by friends
or relatives for your enjoyment.
You can not copy a DVD to a videotape.
Connect your unit and a source (playing) VCR using
the following diagram.
1)Insert a pre-recorded video cassette into the source
(playing) VCR or camcorder.
2)Insert a blank video cassette or one you want to
record over, into the unit’s cassette compartment.
3)Press the SPEED button on remote control to select
the desired recording speed (SP/SLP).
4)Press the CHANNEL button K or L on the unit
until “AUX” appears on the screen.
5)Press the RECORD button on the unit.
6)Begin playback of the tape in the source (playing)
VCR or camcorder.
NOTE:
For best results during copying, use the unit’s front
panel controls whenever possible. The remote control
might affect the source (playing) VCR’s playback
operation.
7)To stop copying, press the STOP/EJECT button on
the unit, then stop the tape on the source VCR or
camcorder.
TV/VCR
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
VIDEO
IN OUT
AUDIO
IN OUT
L
R
[Fig.8]
[Ex: Source (playing)
VCR or camcorder]
Audio/Video
adapter cable
(not supplied)
[This unit]
This function enables you to set a recording length
simply by pressing the REC/OTR button on the unit.
Make sure ...
• The unit is turned on.
• Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape
to the point at which you want to begin recording.)
NOTES:
• You CANNOT start OTR with the remote control.
• Recording starts immediately when the REC/OTR
button is pressed.
• When the REC/OTR button is pressed 18 times,
the unit returns to the Normal Recording mode.
• To stop the OTR operation, press the STOP button
on the unit or on the remote control.
• To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up
momentarily then disappear.)
• Recording stops when 0:00 is reached.
• Please note that in the SLP mode maximum record-
ing time, assuming the tape is started at the begin-
ning, is 8 hours using T-160 (or 6 hours using T-120).
• If the tape runs out before the end time, the unit
will switch to the Stop mode immediately, ejects
the tape and turns itself off.
• If you press the POWER button during OTR, the
unit continues recording until the selected length is
reached.
1
Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL button K or L.
Remember: If the unit is connected to a cable box
or satellite box, the unit must be on CH3 or CH4,
then the channel to be recorded is selected on the
cable box or satellite box.
2 Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3 Begin OTR
Press the REC/OTR button on the
unit as many times as needed. The
recording length will be determined
by the number of times you press the
REC/OTR button. Each additional
push will increase the recording time
by 30 minutes. It is set up to 8 hours.
TV/VCR
OTR(2 : 30)
SP
T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 31