Horizon Fitness 1.3T - Manual (Page 4)


INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
TREADMILL OPERA
TION
LIMITED
W
ARRANTY
TROUBLESHOOTING
&
MAINTENANCE
CONDITIONING
GUIDELINES

INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE YOU
BEGIN
TREADMILL OPERA
TION
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
ASSEMBLY
IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!
During the assembly process of the treadmill there are several areas that special attention must be paid.
It is very important to follow the assembly instructions correctly and to make sure all parts are firmly
tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that
are not tightened and will seem loose and may cause irritating noises. There should be no side-to-side play
in the console masts or any forward and back play in the console assembly or handlebars. If there is any
play in these areas, the treadmill has not been properly assembled. To prevent damage to the treadmill, the
assembly instructions must be reviewed and corrective actions should be taken.
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on
your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side.
Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled
and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. The
enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab
hold of any portion of the incline frame and attempt to lift or move the treadmill. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN INJURY!
Before proceeding, find your treadmill’s serial number
and model name located to the left of the on/off
power switch and power cord and enter it in the space
provided below.
ENTER YOUR SERIAL NUMBER AND
MODEL NAME IN THE BOxES BELOW:
SERIAL NUMBER :
MODEL NAME:
* Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
* Also enter this serial number on your Warranty Card.
1.3T ASSEMBLY
PARTS
1 Power Cord
1 Safety Key
2 Water Bottle Holders
3 Hardware Bags
Left and right outer Console Mast Covers
1 Console Assembly
TOOLS (INCLUDED)
5mm Allen Wrench
Flat Wrench
6mm T-Wrench
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your treadmill, to
prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
If you have questions or if there are any missing parts, contact Customer Tech Support.
Contact information is located on the back panel of this manual.
For a complete exploded diagram, visit us at www.horizonfitness.com
WATER BOTTLE HOLDER
CONSOLE MAST
TRANSPORT WHEEL
DISPLAY
CONSOLE MAST COVER
SAFETY KEY PLACEMENT
CIRCUIT BREAKER
ON/OFF SWITCH
POWER CORD
CONSOLE
TOUCH PAD
GRIP PULSE HANDLE BARS
MOTOR COVER
SIDE RAIL
ROLLER END CAP
RUNNING BELT
REAR ROLLER
ADJUSTMENT BOLTS
TIM E
DIS TAN CE
CAL OR IES PU LSE
INC LIN E SPE ED
1MPH 2MP H 3MPH 4MP H 5MPH 6MP H 7MPH 8MPH 9MP H 10 MPH PRE SS ENT ER TO SET
SPE ED MAG NET IC KEY
1.3T
INC LIN E
SPE ED INC LIN E
%
SPE ED
MP H
STO P HOL D T O R ESE T
STA RT QUI CK STA RT ENT ER CHA NGE DIS PLA Y
1 2 3 4 5 6 7 8 9 1 0
1 2 3 4 5 6 7 8 9 1 0
WARNING
1.3T_Rev.1.4.indd 6-7 7/12/06 8:25:01 AM