Horizon Fitness 1.3T - Manual (Page 5)


INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
TREADMILL OPERA
TION
LIMITED
W
ARRANTY
TROUBLESHOOTING
&
MAINTENANCE
CONDITIONING
GUIDELINES

INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE YOU
BEGIN
TREADMILL OPERA
TION
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
DO NOT CUT STRAPS UNTIL STEP 1-E!*
Disassemble box and remove the
cardboard packaging that is not beneath the treadmill. Do not attempt to lift the
treadmill at this time. Remove plastic wrap from console masts.
Open HARDWARE BAG 1.
Lift LEFT CONSOLE MAST into
upright position. Be sure to hold
the console mast firmly, as it
will not stay in the upright
position on it’s own.
Move LEFT SIDE LINKAGE ARM
into position. Insert BOLT (A)
and tighten.
Repeat on the right side.
Now cut the banding straps and
remove remaining packaging
material.*
PRE-ASSEMBLY
WARNING
ASSEMBLY STEP 1
A
B
C
D
E
BOLT (A)
45 mm
Qty: 2
HARDWARE BAG 1 CONTENTS :
BOLT (A) LOWER
LINKAGE
ARM
BOLT (B) NUT (C)
LINK ARM COVER
TIM E
DIS TAN CE
CAL OR IES PU LSE
INC LIN E SPE ED
1MP H 2MP H 3MP H 4MP H 5MP H 6MP H 7MP H 8MP H 9MP H 10 MPH PRE SS ENT ER TO SET
SPE ED MAG NETI C K EY
1.3T
INC LIN E
SPE ED INC LIN E
%
SPE ED
MP H
STO P HOL D T O R ESE T
STA RT QUI CK STA RT ENT ER CHA NGE DIS PLA Y
1 2 3 4 5 6 7 8 9 1 0
1 2 3 4 5 6 7 8 9 1 0
ASSEMBLY STEP 2
BOLT (A) LOWER
LINKAGE
ARM
BOLT (B) NUT (C)
LINK ARM COVER
TIM E
DIS TAN CE
CAL OR IES PU LSE
INC LIN E SPE ED
1MPH 2MPH 3MPH 4MP H 5MPH 6MP H 7MP H 8MPH 9MPH 10 MPH PRE SS ENT ER TO SET SPE ED MAG NETI C K EY
1.3T
INC LIN E
SPE ED INC LIN E
%
SPE ED
MP H
STO P HOL D T O R ESE T
STA RT QUI CK STA RT ENT ER CHA NGE DIS PLA Y
1 2 3 4 5 6 7 8 9 1 0
1 2 3 4 5 6 7 8 9 1 0
#0-5
#

NN
2UZ

/:-0/
/65
$

NN
2UZ

HARDWARE BAG 2 CONTENTS : Open HARDWARE BAG 2.
Lift CONSOLE (as shown) to lock
it into place.
Insert BOLT (B) through
CONSOLE MAST and secure
using NUT (C).
Repeat on other side.
Note: Do not pinch the wires.
A
B
C
D
$0/40-&
."45
* NOTE: If the straps have been removed
before completing step 1-D and the
linkage arms cannot be aligned, refer
to the TROUBLESHOOTING section
(page 35) in order to restore the
treadmill to its proper position.
ASSEMBLY STEP 3
BOLT (D)
CONSOLE MAST COVER
BOLT (D)
16 mm
Qty: 6
HARDWARE BAG 3 CONTENTS :
WATERBOTTLE
HOLDER
SAFETY KEY
Open HARDWARE BAG 3.
Place CONSOLE MAST COVERS
over CONSOLE MASTS as shown.
Attach CONSOLE MAST COVERS
using 6 BOLTS (D).
Place WATER BOTTLE HOLDERS
and SAFETY KEY into the correct
positions. It is now safe to plug
in your treadmill.
A
B
C
D
YOU’RE FINISHED!
1.3T_Rev.1.4.indd 8-9 7/12/06 8:25:07 AM