Horizon Fitness 2.3T - Manual (Page 4)


INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
TREADMILL OPERA
TION
LIMITED
W
ARRANTY
TROUBLESHOOTING
&
MAINTENANCE
CONDITIONING
GUIDELINES

INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE YOU
BEGIN
TREADMILL OPERA
TION
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
ASSEMBLY
IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!
During the assembly process of the treadmill there are several areas that special attention must be paid.
It is very important to follow the assembly instructions correctly and to make sure all parts are firmly
tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that
are not tightened and will seem loose and may cause irritating noises. There should be no side-to-side play
in the console masts or any forward and back play in the console assembly or handlebars. If there is any
play in these areas, the treadmill has not been properly assembled. To prevent damage to the treadmill, the
assembly instructions must be reviewed and corrective actions should be taken.
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on
your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side.
Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled
and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. The
enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab
hold of any portion of the incline frame and attempt to lift or move the treadmill. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN INJURY!
Before proceeding, find your treadmill’s serial number
and model name located to the left of the on/off
power switch and power cord and enter it in the space
provided below.
ENTER YOUR SERIAL NUMBER AND
MODEL NAME IN THE BOxES BELOW:
SERIAL NUMBER :
MODEL NAME:
* Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
* Also enter this serial number on your Warranty Card.
WATERBOTTLE HOLDER
TOUCHPAD PANEL WITH LED WINDOWS
READING RACK
GRIP PULSE HAND RAILS
SAFETY KEY PLACEMENT
HAND RAILS
MOTOR COVER
SIDE RAIL
ROLLER END CAP
REAR ROLLER ADJUSTMENT BOLTS
CONSOLE
CONSOLE SKIRT
CONSOLE MAST
CIRCUIT BREAKER
ON/OFF SWITCH
POWER CORD
WHEEL LOCKS
SIDE COVER
TRANSPORT WHEEL
RUNNING BELT / RUNNING DECK
c
1 Power Cord
c
1 Safety Key
c
1 Console Skirt
c
1 Console Assembly
c
Left and Right Side Covers
c
Left and Right Console Masts
c
Left and Right Hand Rails (3.3T & 5.3T only)
c
5 Hardware Bags (2.3T has 4 Hardware Bags)
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your treadmill, to
prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
2.3T - 5.3T ASSEMBLY
PARTS TOOLS (INCLUDED)
c
5mm Allen Wrench
c
6mm T-Wrench (2.3T)
c
8mm T-Wrench (3.3T & 5.3T)
c
Flat Wrench
If you have questions or if there are any missing parts, contact Customer Tech Support.
Contact information is located on the back panel of this manual.
For a complete exploded diagram, visit us at www.horizonfitness.com
WARNING
2.3T-5.3T_Rev.2.0.indd 6-7 7/17/06 11:42:57 AM