HP CD-9400 - Manual (Page 7)

7
3. Hold the CD vertically and insert it into the CD slot,
label side to the left.
.
4. To load more CDs, repeatedly press
2
DISC NUMBER
3 (or 2
DISC
3 on the remote) so the desired rack
number appears on the display. Then repeat Step 3.
5. When you finish loading the desired CDs, press OPEN/
CLOSE to close the rack cover.
To remove a CD, select the slot number of the disc you want
to remove, then press
UNLOAD. The rack rotates the
selected disc slot to the front. When the rack cover opens,
remove the selected CD. Press
OPEN/CLOSE to close the rack
cover.
Cautions:
•
Do not try to manually open the rack cover; only use
OPEN/CLOSE.
• Do not load anything other than 5-inch or 3-inch CDs
into the slots. This could damage the CD changer.
• Do not use an adapter for 3-inch CDs. Also, avoid
placing 3-inch CDs between 5-inch CDs as this makes
it hard to remove the 3-inch CDs.
• The CD changer does not play with the rack cover open.
Notes:
•
You can use OPEN/CLOSE to open the rack cover and
remove the disc if the disc to remove is already at the
front of the rack. The display shows
HOLD while the
rack cover is open.
• You can open the rack cover even while a disc is
playing. Hold down
OPEN/CLOSE until the display
shows OPEN . The rack cover opens and the display
shows HOLD . In this case, the rack does not rotate
and you cannot use UNLOAD, SINGLE PLAY/ACCESS,
or
2
DISC NUMBER
3.
BASIC OPERATING INSTRUCTIONS
USING THE REMOTE CONTROL
Many of the CD changer’s buttons also have a
corresponding button on the remote control, and you can
use either the CD changer or the remote control to control
the function.
To use the remote control, point it at the infrared sensor
on the front panel and press the control button.
When the remote control’s operating distance reduces or if
the remote control stops working, replace the batteries.
Note: The remote operates the CD changer from up to 23
feet away and within 30º of the front of the CD changer.
LOADING CDS IN THE RACK
The multi-disc rack holds 100 CDs. The disc slots are
numbered in clockwise order, from 1 to 100, and can hold
either 3-inch or 5-inch CDs.
Follow these steps to load up to 100 CDs in the slots.
1. Press POWER to turn on the CD changer. If necessary,
repeatedly press 2
DISC NUMBER
3 (or 2
DISC
3
on the remote) so the slot number you want appears
on the display.
RANDOM
DISC
ASMS
RANDOM
MODE HI-LITE
CLEAR PROGRAM
PLAY/PAUSE STOP ASMS/SEARCH
UNLOAD OPEN/ CLOSE
BEST PREVIOUS
REPEAT
DISC NUMBER
6 7 ¡ ¢ 4 1
CD • DECK SYNCHRO SYSTEM
RANDOM
MODE HI-LITE
CLEAR PROGRAM
PLAY/PAUSE STOP ASMS/SEARCH
UNLOAD OPEN/ CLOSE
BEST PREVIOUS
REPEAT
DISC NUMBER
6 7 ¡ ¢ 4 1
CD•D DECK SYNCHRO SYSTEM
2. Press UNLOAD to open the rack cover.
Warning: To protect your hearing, set the volume on your
receiver or amplifier to its lowest level before you load and
play a CD.
Caution: Do not set the volume on your receiver or
amplifier too high while playing soft or quiet portions of a
music program. Due to the CD changer’s wide dynamic
range, the speakers might be damaged if the music program
includes a sudden loud passage.
Note: Always handle CDs by their edges. Fingerprints and
scratches on a CD’s surface can prevent the laser beam from
correctly reading the digital information. For more
information, see “CD Care Tips” on Page 15.