Horizon Fitness CX-66 - Manual (Page 4)

BEFORE
YOU
BEGIN
6
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
ELLIPTICAL OPERA
TION
LIMITED
W
ARRANTY
TROUBLESHOOTING
&
MAINTENANCE
CONDITIONING
GUIDELINES
BEFORE YOU
BEGIN
ASSEMBL
Y
7
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ELLIPTICAL OPERA
TION
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
ASSEMBLY STEP 1
TOOLS INCLUDED PARTS INCLUDED
c
5mm L Wrench
c
5mm T Wrench
c
Phillips Screw Driver
c
13/17mm Flat Wrench
c 1 Console
c 1 Console Mast
c 2 Upper Handlebars
c 2 Lower Handlebars
c 2 Lower Link Arms
c 2 Pivoting Foot Pads
c 2 Elbow Covers Sets
c 2 Handlebar Cover Sets
c 2 Mid-Stabilizer Covers
c 2 Rear Stabilizer Caps
c 1 Stabilizer Bar
c 1 Console Mast Boot
c 1 Top Cap
c 2 Pedal Arms
c 2 Roller Wheel Covers
c 6 Hardware Bags
c 1 Power Supply
c 1 Audio Adaptor Cable
SPEAKERS
CONSOLE
UPPER HANDLEBAR
MAIN FRAME
LOWER HANDLEBAR
LOWER LINK ARM
FRONT STABILIZER TUBE
FAN
GRIP PULSE
CONSOLE MAST
TOP CAP
PIVOTING FOOT PAD
PEDAL ARM
REAR STABILIZER CAPS
HANDLEBAR COVER SET
CONSOLE MAST BOOT
ELBOW COVER SET
CUSTOMSTRIDE ™
ADJUSTMENT KNOB
If you have questions or if there are any missing parts, contact Customer Tech Support.
Contact information is located on the back panel of this manual.
MID-STABILIZER COVER
ROLLER WHEEL COVER
PEDAL ARM COVER
For a complete exploded diagram, visit us at www.horizonfitness.com
FRONT STABILIZER TUBE
BOLT (A)
WASHER (B)
WASHER (C)
MAIN FRAME
Quantity
2
Picture
2
2
List
Z24. Wave Washer
Z02. M8X19L Bolt
Z01. 16mm FLat Washer
2 Z07. Plain Washer
2
6
6
4
8
2
2
2
2
2
2
8
6
2
Z03. Spring Washer
Z04. M8x15mm Bolt
Z25. Plain Washer
Z08. Plain Washer
Z12. 44mm Axis
Z13. M8 Nylon Nut
Z14. 60mm Bolt
Z17. M5X12L Screw
Z16. M4X15L Screw
Z30. M4x12L Bolt
Z05. M8x13mm Bolt
Z09. 15.9mm Teflon Washer
Z06. Wave Washer
Z10. M4X15L Screw
MAIN FRAME
TOP CAP
CONSOLE WIRE
GROMMET
FLAT WASHER (A)
SPRING WASHER (B)
BOLT (C)
TOP CAP
CONSOLE MAST BOOT
CONSOLE MAST
MAIN FRAME CONSOLE WIRE
FLAT WASHER (C)
SPRING WASHER (B)
BOLT (A)
WAVY WASHER (D)
FRONT STABILIZER TUBE
BOLT (A)
WASHER (B)
WASHER (C)
MAIN FRAME
Quantity
2
Picture
2
2
List
Z24. Wave Washer
Z02. M8X19L Bolt
Z01. 16mm FLat Washer
2 Z07. Plain Washer
2
6
6
4
8
2
2
2
2
2
2
8
6
2
Z03. Spring Washer
Z04. M8x15mm Bolt
Z25. Plain Washer
Z08. Plain Washer
Z12. 44mm Axis
Z13. M8 Nylon Nut
Z14. 60mm Bolt
Z17. M5X12L Screw
Z16. M4X15L Screw
Z30. M4x12L Bolt
Z05. M8x13mm Bolt
Z09. 15.9mm Teflon Washer
Z06. Wave Washer
Z10. M4X15L Screw
MAIN FRAME
TOP CAP
CONSOLE WIRE
GROMMET
FLAT WASHER (A)
SPRING WASHER (B)
BOLT (C)
TOP CAP
CONSOLE MAST BOOT
CONSOLE MAST
MAIN FRAME CONSOLE WIRE
FLAT WASHER (C)
SPRING WASHER (B)
BOLT (A)
WAVY WASHER (D)
A) Open HARDWARE BAG FOR STEP 1.
B) Slide the CONSOLE MAST BOOT followed by the TOP CAP over the CONSOLE MAST.
C) Carefully pull the CONSOLE WIRES through the CONSOLE MAST using the twist tie located inside the
CONSOLE MAST.
D) Attach the sides of the CONSOLE MAST to the MAIN FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4
FLAT WASHERS (C).
E) Attach the front of the CONSOLE MAST to the MAIN FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2
WAVY WASHERS (D).
F) Slide CONSOLE MAST BOOT down to seal the console mast hole.
BOLT (A)
15 mm
Qty: 6 SPRING WASHER (B)
Qty: 6 FLAT WASHER (C)
20 mm
Qty: 4 WAVY WASHER (D)
17 mm
Qty: 2
angle view
HARDWARE BAG FOR STEP 1 CONTENTS :
CX-66_Elliptical_Rev.1.6.indd 6-7 6/13/07 1:26:03 PM