Document Outline

• Notices
  • FCC notice
  • Class A equipment
  • Shielded cables
  • Peripheral devices
  • Use conditions
  • Canadian users
  • Laser compliance statement
• Important safety instructions
• 1 System information
  • Product briefing
    • Processor
    • Memory subsystem
    • Storage
    • Graphics interface
    • Networking
    • I/O ports
  • Caring features
  • Product specification summary
• 2 System tour
  • System board
    • Connector and Header Locations
    • Configuration Jumpers
    • Serial Port Configuration Jumper
    • BIOS Select Jumper
    • Back Panel Connectors
    • External and internal structure
    • Front panel
    • Rear view
    • Optional Peripherals
    • Internal components
• 3 Getting Started
  • Setting up the system
    • Preinstallation requirements
  • System startup
    • Turning on the system
    • Turning off the system
    • Power-on problems
• 4 Configuring the system
  • Upgrading the system
    • Installation precautions
  • Opening the server
    • Before opening the server
    • Removing the Chassis Cover
    • Installing the Chassis Cover
  • Removing and Installing the Front Bezel
    • Removing the Front Bezel
    • Installing the Front Bezel
  • Removing and Installing the Processor Air Duct
    • Removing the Processor Air Duct
    • Installing the Processor Air Duct
  • Removing and Installing the Air Baffle
    • Removing the Air Baffle
    • Installing the Air Baffle
  • Installing and Removing a Hard Disk Drive
    • Installing a Fixed SATA Hard Disk Drive
    • Removing a Fixed SATA Hard Disk Drive
  • Installing a SATA or SCSI Hot-swap Hard Disk Drive
    • Removing a SATA or SCSI Hot-swap Hard Disk Drive
  • Installing or Removing a Floppy Drive
    • Installing a Floppy Drive into Slimline Bay (Backplane Installed)
    • Removing a Floppy Drive from the Slimline Bay (Backplane Installed)
    • Installing a Floppy Drive into Slimline Bay (No Backplane Installed)
    • Removing a Floppy Drive from the Slimline Bay (No Backplane Installed)
    • Installing a Floppy Drive into the Converted Hard Drive Bay (Backplane Installed)
    • Removing a Floppy Drive from the Converted Hard Drive Bay
  • Installing or Removing a DVD/CD-RW or CD-ROM Drive
    • Installing a DVD/CD-RW or CD-ROM Drive into Slimline Bay (Backplane Installed)
    • Removing a DVD/CD-RW or CD-ROM Drive from the Slimline Bay (Backplane Installed)
    • Installing DVD/CD-RW or CD-ROM Drive into Slimline Bay (No Backplane Installed)
  • Installing and Removing a PCI Riser Connector
    • Installing a PCI Riser Connector
    • Removing a PCI Riser Connector
  • Installing and Removing a PCI Add-in Card
    • Installing a PCI Add-in Card
    • Removing a PCI Add-in Card
  • Installing and Removing the SATA or SCSI Backplane (Optional)
    • Removing the SATA or SCSI Backplane
    • Installing the SCSI or SATA Backplane
  • Processor Installation and Upgrade
    • Installing or Replacing the Processor
    • Installing the Processor
    • Installing the Heat Sink(s)
    • Removing a Processor
  • Memory Installations and Upgrade
    • Upgrading the system memory
    • Memory Sparing
    • Installing and Removing Memory
    • Installing DIMMs
    • Removing DIMMs
• 5 BIOS setup
  • Using the BIOS Setup Utility
    • Entering BIOS
    • If You Cannot Access Setup
    • Setup Menus
    • BIOS Setup Utility
    • BIOS Setup Keyboard Command Bar Options
    • Main
    • Advanced
    • Upgrading the BIOS
    • Clearing the Password
    • Clearing the CMOS
• 6 Troubleshooting
  • Hardware Diagnostic Testing
  • Specific Problems and Corrective Actions
• Appendix A: Management software installation
  • Installing ASM
    • System requirements
    • System setup
  • Tool-less rail kit installation
    • Setting the Multi-Pin Adapters for Rack Type
    • Installing the Slide Rails into the Rack
    • Installing the Component into the Slide Rails
    • Required Installation Position of the CMA
    • General Safety Information
• Appendix B: Tool-less rail kit installation
• Appendix C: Sensor Table
  • Sensor Table
• Appendix D: SATA RAID Configuration
  • Configuring the onboard SATA RAID
    • How to enable the onboard SATA RAID function
    • How to create RAID 1 volume
    • Loading onboard SATA RAID default setting
• Index