APC 2200 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for 2200 APC
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 21 |
| Size: | 332 KB |
Show table of contents
Read manual
Document Outline
- Product Description
- Safety
- Product Overview
- Specifications
- Installation
- Connect Equipment to the UPS
- 1 . Connect equipment to the outlets on the rear panel of the UPS. Do not use extension cords, pl...
- 2 . Connect the UPS to the building utility power. Connect the UPS to a two-pole, three-wire, gro...
- 3 . Press the On/Off button on the front panel of the UPS to apply power to the unit and all conn...
- 4 . To use the UPS as a master on/off switch, turn on all the equipment that is connected to the ...
- Rear Panel Features
- Display Interface
- Overview
- Using the display interface
- Standard menus
- • Operating mode
- • Switched Outlet status, On or Off
- • Efficiency of the UPS
- • Information about the load
- • Battery capacity
- • Estimated runtime
- • Input and output voltage and frequency
- • Information about the last transfer to battery power
- • Self-test results
- • Language
- • Local power quality: Good, Fair, Poor
- • Choose Standard or Advanced menus
- • LCD Display mode, Always On or Power-Saving
- • Audible alarms
- • Reset to Factory Defaults
- • Unit model number
- • Serial number
- • Battery installation date
- • Suggested battery replacement date
- • Replacement Battery Cartridge model number
- • UPS firmware version
- Advanced menus
- • Energy meter
- • Load current
- • Status of the Switched Outlet Group
- • Battery voltage
- • Main and Switched Outlet Group—delays and settings
- • High and lower transfer points
- • Sensitivity settings
- • Date of last battery replacement
- • Hardware version
- • Software version
- • NMC information (if applicable)
- UPS Settings
- Start-up Settings
- General Settings
- • 127 Vac
- • 130 Vac
- • 133 Vac
- • 136 Vac
- • 253 Vac
- • 257 Vac
- • 261 Vac
- • 265 Vac
- • 97 Vac
- • 100 Vac
- • 103 Vac
- • 106 Vac
- • 196 Vac
- • 200 Vac
- • 204 Vac
- • 208 Vac
- • High: The UPS will go on battery power more often to provide the cleanest power supply to the c...
- • Low: The UPS will tolerate more fluctuations in power and will go on battery power less often.
- • Never
- • Start-up only
- • Frequency of test (days)
- Main Outlet Group and the Switched Outlet Group
- Overview
- Using the Main Outlet Group and the Switched Outlet Group
- Customize the Main Outlet Group and the Switched Outlet Group
- Network Management Card Settings
- Emergency Power Off
- Service
- 1 . Review the Troubleshooting section of the UPS manual to eliminate common problems.
- 2 . If the problem persists, contact APC Customer Support through the APC Web site, www.apc.com.
- a. Note the model number and serial number, located on the rear of the unit, and the date of purc...
- b. Call APC Customer Support and a technician will attempt to solve the problem over the phone. I...
- c. If the unit is under warranty, the repairs are free.
- d. Service procedures and returns may vary internationally. Refer to the APC Web site for country...
- 3 . Pack the unit in its original packaging. If this is not available, refer to www.apc.com to ob...
- a. Pack the unit properly to avoid damage in transit. Never use foam beads for packaging. Damage ...
- b. For the UPS, always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department ...
- c. Internal batteries may remain connected in the XLBP during shipment (if applicable, not all un...
- 4 . Write the RMA# provided by Customer Support on the outside of the package.
- 5 . Return the unit by insured, pre-paid carrier to the address provided by Customer Support.
- Transport the unit
- APC Worldwide Customer Support
- LIMITED WARRANTY