Applied Motion STAC6-Q Instruction Manuals and User Guides
We have 2 Instruction Manuals and User Guides for STAC6-Q Applied Motion
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 101 |
| Size: | 4.13 MB |
Show table of contents
Read manual
Document Outline
- Table 1: Bit Rate Switch Settings
- Table 2: Modes of Operation
- Table 3: CiA 301 Object Descriptions
- Table 4: Tuning Parameter setting
- Table 5: CiA 402 Objects
- Table 6: MOONS’ Manufacture Specific Objects
- Table 7: User Defined Registers in CANopen and Q Programmer
- Table 8: Object Dictionary Structure
- Table 9: Description of SYNC COB-ID entry
- Table 10: Description of PDO COB-ID entry
- Table 11: Description of transmission type
- Table 12: Controlword Data Description
- Table 13: Device Control Command Bit Patterns (Bits 0-3 and 7)
- Table 14: Bits in the statusword
- Table 15: Device State Bits
- Table 16: Parameter Scaling Chart
- Table 17: Object 603Fh CiA 402 Error Codes
- Table 18: Object 700Bh DSP Status Codes
- Table 19: Single Set-Point Profile Position Move
- Table 20: Multiple Set-Point Profile Position Move with Stopping Between Moves
- Table 21: Multiple Set-Point Profile Position Move with Continuous Motion
- Table 22: Multi-Set-Point Profile Position Move with Immediate Change in Motion
- Table 23: Profile Velocity Mode Example
- Table 24: Profile Torque Mode Example
- Table 25: Understanding NMT States
- Table 26: Example - NMT Data Frame
- Table 27: Enable SDO Use
- Table 28: TPDO Transmission Types
- Table 29: PDO Mapping
- Table 30: PDO Mapping Example
- Table 31: PDO Mapping - Stepper
- Table 32: PDO Mapping - Servo
- Table 33: PDO COB-IDs
- Figure 1:
- Figure 2:
- Figure 3:
- Figure 4:
- Figure 5:
- Figure 6:
- Figure 7:
- Figure 8:
- Figure 9:
- Figure 10:
- Figure 11:
- Figure 12:
- Figure 13:
- Figure 14:
- Figure 15:
- Figure 16:
- Figure 17:
- Figure 18:
- Figure 19:
- Introduction
- User Advisory:
- Drive Setup
- Supported CiA 402 Modes of Operation
- Object Dictionary
- General Purpose Registers
- Appendix A - The Object Dictionary
- Appendix B - Parameter Unit Scaling
- Appendix C - Response Codes
- Appendix D - Profile Position Mode
- Appendix E - Profile Velocity Mode
- Appendix F - Homing Methods
- Set Running Parameters
- Enable Homing Mode
- Starting the Homing Procedure
- Homing Method Diagrams
- Homing Method 1
- Homing Method 2
- Homing Method 3
- Homing Method 4
- Homing Method 5
- Homing Method 6
- Homing Method 7
- Homing Method 8
- Homing Method 9
- Homing Method 10
- Homing Method 11
- Homing Method 12
- Homing Method 13
- Homing Method 14
- Homing Methods 15 and 16
- Homing Method 17
- Homing Method 18
- Homing Methods 19 and 20
- Homing Methods 21 and 22
- Homing Methods 23 and 24
- Homing Methods 25 and 26
- Homing Methods 27 and 28
- Homing Methods 29 and 30
- Homing Methods 31 and 32
- Homing Method 33
- Homing Method 34
- Homing Method 35
- Appendix G - Profile Torque Mode (Servo Only)
- Appendix H - Q Program Mode
- Appendix I - Understanding NMT States
- Appendix J - SDO and PDO Access
- PDO Access
- Appendix K - Operation Mode Specific Control and Status Word
- Appendix L – Example Programs
| Recognized languages: | English |
|---|---|
| Pages: | 57 |
| Size: | 3.49 MB |
Show table of contents
Read manual
Document Outline
- Safety Instructions
- Over-Current Protection
- Block Diagrams
- Motion Control Options
- Getting Started
- Connecting to the PC using RS-232
- Connecting to the PC using RS-485
- Connecting to the CANopen Network
- Connecting AC Power
- Connecting the Motor
- Connecting Other Motors
- Connecting an Encoder
- Wiring Inputs and Outputs
- Connecting Digital Inputs on the IN/OUT1 connector
- Connecting Digital Outputs on the IN/OUT1 connector
- Connecting Analog Inputs on the IN/OUT1 connector
- Connecting Inputs and Outputs to IN/OUT2
- Connecting Digital Inputs on the IN/OUT2 connector
- Connecting Digital Outputs on the IN/OUT2 connector
- Connecting Analog Inputs on the IN/OUT2 connector
- Recommended Motors
- Motor Dimensions
- Torque-Speed Curves
- Mounting the Drive
- Mechanical Outline
- Technical Specifications
- Mating Connectors and Accessories
- Alarm Codes