Document Outline

• Copyright
• Table of Contents
• Feature Guide
  • How The Manual Is Organized
  • Main Features
  • Software
  • The P/I-P55SP4 Package
  • Static Electricity Precautions
  • Mainboard Layout
  • Using Your Mainboard
    • Hardware Settings
      • Jumpers and caps
      • Jumper cap 3-pin jumper 2-pin jumper Jumper block
        • Jumper diagrams
      • The System Configuration Record
        • Important:
    • System IRQs
    • BIOS-Supported Enhanced IDE Features
      • Large IDE Hard Disks
      • Other IDE Devices
      • Dual IDE Channel Support
      • Faster Data Transfer
      • Power Conservation
      • SCSI BIOS Firmware & The Optional SC-200 Controller Card
• Upgrade Guide
  • Installing Expansion Cards
    • Installation Procedure
    • Assigning System IRQs for Expansion Cards
      • Assigning DMA Channels For ISA Cards
      • The MediaBus Slot
  • Upgrading System Memory
    • Configuring System Memory
      • Memory Combinations
    • Installing SIMMs
      • Installing a Memory Module
      • Module Sockets & Orientation
  • I
    • Updating the Flash BIOS
      • BIOS With Boot Block Update Procedure
• Software Guide
  • Award BIOS Setup
    • Main Program Screen
    • Standard CMOS Setup
      • Standard CMOS Setup Screen
      • Date & Time
      • Hard Drive Type
      • Floppy Disk Drives
      • Video Display Types
      • Error Handling
    • BIOS Features Setup
      • BIOS Features Setup Screen
      • Virus Protection
      • Cache Control
      • Boot Up Features
      • IDE Block Mode
      • Keyboard Interface
      • Security Option Password Control
      • PS/2 Mouse
      • Shadow Controls
      • Chipset Features Setup
        • Chipset Features Screen
    • Power Management Setup
      • The Power Management Setup Screen
      • Power Management
      • Video Off
      • Suspend Switch
      • Doze & Standby Speeds
      • PM Timers
      • PM Events
      • IRQS to IRQ15 Individual Settings
    • PCI/PNP & Onboard i/0 Setup
      • PCI/PNP & Onboard I/O Setup Screen
      • PNP (Plug And Play)
      • Controller Settings
      • Serial Ports
      • Parallel Port
      • Parallel Port Mode
      • UART2 Use Infrared
      • Internal PCI/IDE, IDE PIO & Prefetching Settings
    • Load BIOS Defaults
      • Load BIOS Defaults Screen
    • Load Setup Defaults
      • Load Setup Defaults Screen
    • Setting Supervisor & User Passwords
      • Password Setting
    • IDE HDD Auto Detection
      • IDE HDD Auto Detection Screen
    • Save And Exit Setup
    • Exit Without Saving
  • NCR SCSI BIOS & Drivers
  • Flash Memory Writer Utility
    • The Flash Memory Writer Utility Screen
    • The Advanced Features Screen
• Technical Summary
  • Jumper Setting Summary
    • PS/2 Mouse Port Selector: JP5
    • PS/2 Mouse PS/2 Mouse
    • SRAM Type Selector JPG, JP7, JP8 & JP9
    • Mixed Mode SRAM
    • Level 2 Cache Size: JP10&JP11
    • CPU External Clock Speed Selector: JP12, JP13 & JP14
      • 66MHz Ext. 60MHz Ext.
      • Note: JP14 default is 1&2 for all settings, do not change it
    • 1.5xExtClk 2xExtClk 2.5xExtClk SxExtClk
    • 3.3V+5%
    • STD/VR
    • Voltage Regulator Module Selector: JP32, JP33, JP34, JP35
      • Note: Revisions 1.3 or later have three additional jumpers, JP1A, JP1B and JP1C. The default settings are shown helow.
    • UART2/IR Selection: JP1A & JP1B
    • Super I/O Selection: JP1C
    • Level 2 Cache Options
      • Important:
      • 256KB
      • 32K8x8
      • Cache module installation
      • 512KB
      • 64K8x8
      • or
      • 1MB
  • External Connections
    • Case Feature Connectors
    • SMi Suspend Switch ^
    • Keylock
    • Speaker
      • Other Feature Connectors
      • I/O Port Connectors
    • Port & Controller Cables
      • Parallel ribbon cable
    • Connecting A Power Supply
  • The PCI-SC200 SCSI Interface Card
    • The PCTSC200 SCSI Interface Card
    • Internal SCSI ribbon cable connector
    • External SCSI 2 cable connector
    • PCI edge connector
    • Setting Up the PCI-SC200
      • Setting the INT Assignment
      • JPl & 2: Interrupt settings
      • INT A
      • (default)
      • INTB
      • INTO
      • INTO
        • Terminator Settings
        • JP5: Terminator setting
      • Termination
      • Disabled
        • Example 1: Only internal or only external devices connected
        • Example 2: Both internal and external devices connected
    • SCSI ID Numbers
  • Declaration of Conformity