Document Outline

• Regulatory Notices
• Getting Started
  • Mode Comparison
• Operations Overview
  • Cv2 Capabilities (Advanced Mode)
    • What constitutes an alarm?
    • How are alarms processed?
    • What should occur when an alarm is detected?
    • How do you want to respond to an alarm call?
    • What if an alarm is not acknowledged?
    • What do you want the Cv2 to do when you call it?
    • Sending remote control commands
  • Cv2 Capabilities (Basic Mode)
    • What constitutes an alarm?
    • How are alarms processed?
    • What should occur when an alarm is detected?
    • How do you want to respond to an alarm call?
    • What if an alarm is not acknowledged?
    • What do you want the Cv2 to do when you call it?
    • Sending remote control commands
  • Indicators
  • Troubleshooting
• Installation
  • Antenna requirements
  • Mounting
  • Input port connections
    • Ground closure
    • +12 volt signal
    • +5 volt signal
    • Analog input (advanced mode)
  • Output port
  • Configuration port connection
• Configuration using the PC
  • PC requirements
  • Installing the program
  • Starting the program
  • How to access programming functions
  • Program functions - Advanced mode
    • File operations
      • File Open
      • File Save As
      • File Save
    • Summary
    • Change Mode
    • Hardware
    • General
    • Groups
    • Points
    • Directories
    • Programming
  • Program functions - Basic mode
    • File operations
    • Summary
    • Change Mode
    • Alarms
    • Controls
    • General
    • Programming
• Configuring the Cv2 - Advanced mode
  • Hardware section
    • Digital Input
    • Watchdog Input
    • Interval Input
    • Totalizer Input
    • Analog Input
    • On/Off Output
    • Timed Output
  • Points Section
    • Common settings
      • I/O port selection
      • Point name
      • Using Group
      • Enabled
    • Digital and Watchdog Points
      • Alarm State
      • DTMF Tag
    • Interval Point
    • Totalizer Point
      • Decimal Place
      • Clear Code
      • Units
    • Analog Point
      • Calibrate
      • Binary Values
      • Decimal Values
      • Hysterysis
      • Units
    • On/Off Output Point
      • DTMF On Code
      • DTMFOff Code
    • Timed Output Point
      • DTMF On Code
      • DTMF Off Code
  • Group Section
    • Group Name
    • Acknowledge Code
    • Interrogate Code
    • Enable This Group
    • Enable Auto Ack
    • Enable Ack Request
    • Timers
      • Short Timer
      • Short Cycles
      • Long Timer
    • Shift Selection
    • Special Function Outputs
      • Alarm Active
      • New Alarm
      • Acknowledge Received
    • Special Function Input - Ack In
  • Directories
    • Dial
    • Wait
    • Auto Ack
    • DTMF
    • Alert
    • Voice
    • Answer
    • Signal
    • Delete
  • General
    • Site Name
    • Security Level
      • Level 1
      • Level 2
      • Level 3
    • Access Code
    • Shift Change Code
    • Temporary Acknowledge Time
    • Call Progress
    • Ring output
    • Modem CD
    • Enable Modem Code
    • Rings Before Answer
  • Configuration Programming
    • Configuration Data
    • Voice Messages
    • Vocabulary
• Configuring the Cv2 - Basic Mode
  • Alarms Section
    • Directory
    • Format
    • Debounce
  • Control Section
    • Format
    • DTMF On Code
    • DTMF Off Code
    • Interval
  • Directories
    • Insert
    • Delete
    • Edit
    • Advanced
    • Acknowledge Code
    • Interrogate Code
    • Cycle Timer
  • General
• Remote Data Access
• Voice Storage and Configuration with a Telset
  • Setup
  • Access
  • Programming Commands
  • Telset Programming Summary
  • Programming Flowchart
• Voice Editor
  • Voice Editor
  • Wave File Conversion
• Specifications
• Transceiver Codes
• Warranty