Bosch WAP24202UC Instruction Manuals and User Guides
We have 4 Instruction Manuals and User Guides for WAP24202UC Bosch
Manuals
Read manual
Read manual
| Recognized languages: | English |
|---|---|
| Pages: | 36 |
| Size: | 4.84 MB |
Show table of contents
Read manual
Document Outline
- en-us Use and care manual
- Table of contentsen-us Use and care manual
- Important information
- Customer service
- IMPORTANT SAFETY INSTRUCTIONS
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- Introduction to your new washer
- Special features
- Environmentally friendly use of your washer
- Length of power cord and water supply hoses
- Installation types
- Introduction
- Tools needed
- Waste disposal
- Parts provided with your washer
- Set up on a pedestal with drawer
- Installation checklist
- Importance of installing on a solid, level floor
- Remove the transport bolts
- 9 CAUTION
- 1. Remove hoses from the brackets.
- 2. Loosen and remove all 4 transport bolts. Remove the sleeves. Take the power cable out of the brackets.
- 3. Place covers over the transport bolt holes Four plastic covers are provided in the small parts bag included with your washer. Separate these covers and install one in each hole where the transport bolts were removed. Lock covers firmly by pressing...
- NOTICE:
- Water connections
- Leveling the washer
- 1. Install the washer on a level and solid surface, preferably in a corner of a room.
- 2. If the floor is uneven (or unlevel) adjust the washer feet as required to level the washer. Do not place anything under the washer feet to help level the washer.
- 3. Extend the washer feet no more than is necessary. The more the feet are extended, the more vibration the washer will experience. Start with the washer feet turned all the way in and adjust each foot as necessary.
- 4. Use a bubble level to check the top of the washer to make sure it is level side to side and front to rear.
- 5. Press down on each corner of the washer top to make sure the washer doesn’t “wobble“. There should be no "give" or movement. All four washer feet should press equally against the floor. This is just as important as the washer being level to ...
- 6. When the washer is level and does not wobble, lock the washer feet in place by tightening the locknuts against the washer bottom. Be sure to do this without changing the height of the foot (hold the foot while tightening the locknut).
- 1. After determining which washer feet need to be extended, have someone lift up on the washer slightly to take pressure off the foot to be adjusted.
- 2. Turn the grey plastic foot to extend it downward as far as necessary to raise the corner of the washer the correct amount to level the washer.
- 3. When the height of the foot is correct, use a 17 mm open end wrench to tighten the locknut against the washer bottom. The locknut should be tight against the bottom of the washer to lock the foot in place.
- 1. Install the washer on a level and solid surface, preferably in a corner of a room.
- Electrical connection
- Transporting the washer
- 1. Disconnect the washer power cord from the wall outlet.
- 1. Remove all four transport bolt hole covers.
- 1. Each assembly consists of a plastic bushing and a bolt that extends through the bushings. Unscrew the bolt until the threaded end is flush with the end of the plastic bushing.
- 2. Insert the transportation bolt and bushing assembly as shown. The metal housing slides around the bolt through the slot in the plastic bushing as the bushing is slid into place. The open part of the bushing slot should be facing the direction show...
- 3. When the bolt is in place screw it in until the bolt threads engage the drum. Double check and ensure bolts are screwed into threaded holes and not into adjecent cracks or crevices. Repeat the process for all 4 transportation bolt assemblies befor...
- Getting to know your appliance
- Display field
- Sorting the Laundry
- Identifying and treating stains
- Starching
- Dyeing/bleaching
- Soaking
- Changing the spin speed range
- Delay Start
- Easy Iron
- Prewash/Pre Treat
- Before loading your first load of laundry
- Using the cycle selector to choose a wash cycle
- Changing default cycle settings
- Selecting additional cycle settings
- Loading the laundry
- Filling the detergent and additives compartments
- Starting the cycle
- Child lock
- Selecting a different cycle
- Pausing/Continuing the cycle
- Cancel cycle
- Cycle end with rinse stop
- Cycle end
- Removing laundry/switching the appliance off
- Cleaning the housing and control panel
- Cleaning the drum
- Descaling the washer
- Cleaning the detergent dispenser
- 1. Open the dispenser drawer fully. Press down on the drawer catch (1) and pull the drawer (2) from the washer housing.
- 2. Remove the liquid detergent insert (3) by grasping it and pulling it upwards from the detergent dispenser drawer.
- 3. Clean the insert by holding it under warm running water. Lightly wipe away any remaining detergent residue.
- 4. Reinsert the liquid detergent insert and slide the detergent dispenser drawer back into place and close the drawer securely.
- Tip:
- 1. Open the dispenser drawer fully. Press down on the drawer catch (1) and pull the drawer (2) from the washer housing.
- Cleaning the water inlet strainers
- Cleaning the drain pump
- 9 WARNING
- 1. If the washer has not been drained, try to drain it now. Turn the cycle selector to the Spin/Drain cycle, select No spin and press the Start/Pause button. Wait a few moments to let the cycle drain the water from the drum. If the pump is totally bl...
- 2. Shut off the tap so that no more water flows in and has to be drained.
- 3. Open and remove the service cover.
- 4. Loosen the screws and remove the protective film.
- 5. Use the pull-out drain hose located in the pump access opening to drain the remaining water into a suitable container (up to 5.3 U.S. gallons/20 liters of water may be drained). Pull the sealing cap from the hose and lay the hose over the side of ...
- 6. Turn the pump cover counterclockwise to remove it. A small amount of residual water may flow out when the cover is removed. Clean the interior of the pump housing, removing any debris or foreign objects. Check to be sure the impeller wheel at the ...
- 7. Screw the protective film on the pump on again.
- 8. Insert the service cover snap it in, and close it.
- NOTICE:
- Troubleshooting
- Emergency door lock release
- 9 WARNING
- 9 WARNING
- 9 CAUTION
- 1. Turn the washer off by rotating the cycle selector to the Off position. Any running program will then be cancelled. Disconnect the mains plug.
- 2. Allow the water in the drum to cool off.
- 3. Allow the washer drum to come to a stand still (no longer spinning).
- 4. Before opening the washer door, perform the drain procedure included in the pump maintenance section following.
- 5. Loosen screws and remove the protective foil.
- 6. The washing machine door can then be opened.
- 7. The door can then be opened.
- Emergency door lock release
- Troubleshooting
- Error messages
| Recognized languages: | English |
|---|---|
| Pages: | 3 |
| Size: | 718 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 16 |
| Size: | 1.32 MB |