Document Outline

• SCOPE
• 2 MARKINGS
  • 2.1 Transmitter [TB8-xx-xx-xx-03] for use with Sensor Head [SH-xxx-xx-xA-xxx-03]:
  • 2.2 Sensor Head [SH-xxx-xx-xA-xxx-03]:
  • 2.3 Transmitter [TB8-xx-xx-xx-04]:
• 3 ATEX ZONE 2 SPECIAL CONDITIONS OF USE RELATED TO THE SYMBOL “X”
  • 3.1 Transient Protection
  • 3.2 Electrostatic Charging
  • 3.3 Cable Glands
  • 3.4 Control Drawings
  • 3.5 Environment
• 4 STANDARDS
• 5 CONTROL DRAWINGS
• 6 SPECIFICATIONS
  • 6.1 Electrical Parameters
  • 6.2 Maximum Surface Temperatures
• 7 OPERATING CONDITIONS UNDER WHICH THIS PRODUCT MAY BE SAFELY USED
  • 7.1 Scope
  • 7.2 Hazardous Rating Location of Facility Where It Is To Be Installed
    • 7.2.1 System including TB8-xx-xx-xx-03 Transmitter
    • 7.2.2 System including TB8-xx-xx-xx-04 Transmitter
  • 7.3 Installation Site Ambient Temperature, Pressure, Humidity
    • 7.3.1 Temperature
    • 7.3.2 Barometric Pressure
    • 7.3.3 Humidity
  • 7.4 Water Spray and Dust
  • 7.5 Explosive Gasses
  • 7.6 Condition of piping
  • 7.7 Chemical Environment
  • 7.8 Mains Power
• 8 SUPPLEMENTARY INSTRUCTIONS FOR SAFE ASSEMBLY AND INSTALLATION
  • 8.1 Use Control Drawing, Install Per Code
  • 8.2 Make Correct Terminal Block Connections
  • 8.3 Use Cable Glands and/or Conduit Entries
    • 8.3.1 Selection of Cable Glands
    • 8.3.2 Selection of Conduit Fittings
  • 8.4 Wire With Power OFF
  • 8.5 Wire Securely to Terminals and Route Neatly
  • 8.6 No Foreign Objects
  • 8.7 Avoid Leaky Pipes
  • 8.8 Seal Sensor Head Cover
  • 8.9 Secure The Access Panel.
• 9 SUPPLEMENTARY INSTRUCTIONS FOR SAFELY PUTTING INTO SERVICE
  • 9.1 Prior to Applying Power
  • 9.2 Apply Power
  • 9.3 Perform Setup
  • 9.4 Verify Proper Operation
• 10 SUPPLEMENTARY INSTRUCTIONS FOR SAFE USE (NORMAL OPERATION WITH NO OPERATOR INTERVENTION)
  • 10.1 Keep Enclosures Closed During Use
    • 10.1.1 Transmitter
    • 10.1.2 Sensor Head
  • 10.2 Periodic Inspections
    • 10.2.1 Transmitter Inspections
    • 10.2.2 Sensor Head Inspections
    • 10.2.3 Cables Inspections
  • 10.3 Problems Found During Inspection
• 11 SUPPLEMENTARY INSTRUCTIONS FOR SAFE ADJUSTMENT
  • 11.1 General
  • 11.2 Transmitter Adjustments
    • 11.2.1 Use of Keypad and RESET Switch
    • 11.2.2 Use of USB Memory Stick Interface
    • 11.2.3 Use of RJ45 Ethernet Connector Interface
    • 11.2.4 Use of DB9 RS232 Connector Interface
  • 11.3 Sensor Head Adjustments
• 12 SUPPLEMENTARY INSTRUCTIONS FOR SAFE MAINTENANCE, SERVICING AND EMERGENCY REPAIR
  • 12.1 General
    • 12.1.1 UOS, OFF And No Explosive Gasses Present
    • 12.1.2 Notify Control Room
  • 12.2 Transmitter
    • 12.2.1 General
      • 12.2.1.1 Ensure There Are No Explosive Gases Present
      • 12.2.1.2 Keep Clean and Dry
    • 12.2.2 Mains Power OFF
    • 12.2.3 Fuse Replacement
    • 12.2.4 Sensor Terminal Blocks
    • 12.2.5 Customer Input / Output and Fieldbus Terminal Blocks
    • 12.2.6 Electrical Circuitry and Electro-Static Discharge (ESD)
  • 12.3 Sensor Head
    • 12.3.1 General
    • 12.3.2 Sensor Head Electrical Connector
    • 12.3.3 Access Panel
    • 12.3.4 Sensor Band
      • 12.3.4.1 Use of Access Panel
      • 12.3.4.2 Safety Procedure for Damaged Sensor Bands
• 13 SUPPLEMENTARY INSTRUCTIONS FOR SAFE DISASSEMBLY OR DISPOSAL
  • 13.1 Most Warnings Same As For Maintenance
  • 13.2 General
    • 13.2.1 Dead Circuits
    • 13.2.2 Disposal Issues
  • 13.3 Sensor Band
    • 13.3.1 Damaged Sensor Bands
    • 13.3.2 Undamaged Sensor Bands
• 14 TRAINING
• 15 CONTACT INFORMATION