Document Outline

• 542-02.pdf
  • 2
    • Setting Up Your CD-ROM Drive
      • Figure 2-1: Items required for setting up your CD-ROM drive.
      • Figure 2-2: IDE CD-ROM interface card.
      • Figure 2-3: CD audio cable.
    • Installing Your Drive
      • Inserting Your Drive into Your System
        • 1. Switch off your system and all peripheral devices.
        • 2. Touch a metal plate on your system to ground yourself and discharge any static electricity.
        • 3. Remove the cover from your system as illustrated in Figure 2-4. If your computer differs from ...
          • Figure 2-4: Removing the computer cover of your system.
        • 4. Locate a 5¹" drive bay for your CD-ROM drive.
        • 5. Vacate a drive bay. If a disk drive is positioned above your vacant drive bay, loosen the scre...
          • Figure 2-5: Vacating a drive bay.
        • 6. Insert your CD-ROM drive into the vacant drive bay as shown in Figure 2-6.
          • Figure 2-6: Inserting your CD-ROM drive.
      • Connecting Cables to Your Drive’s Rear Panel
        • 2. Connect the power cable to the CD-ROM drive as shown in Figure 2-7.
          • Figure 2-7: Connecting power cable to your CD-ROM drive.
        • 3. Connect the data cable to the CD-ROM drive as shown in Figure 2-8. Make sure you align the col...
          • Figure 2-8: Connecting data cable to your CD-ROM drive.
        • 4. If you are connecting your drive to an audio card, connect the CD audio cable to the CD-ROM dr...
          • Figure 2-9: Connecting CD audio cable to your CD-ROM drive.
      • Connecting Cables to Your Card
        • Connecting Cables to Your Audio Card
          • 1. Connect the data cable to your audio card as shown in Figure 2-10. Make sure you align the col...
            • Figure 2-10: Connecting data cable to the audio card.
          • 2. Connect the CD audio cable to your audio card as shown in Figure 2-11.
            • Figure 2-11: Connecting CD audio cable to the audio card.
          • 3. Slide the drives back into place and fasten them to your system as shown in Figure 2-12.
            • Figure 2-12: Fastening the drives to your system.
          • 4. Switch on your system.
          • 5. Proceed to the section “Installing the Software” in this chapter.
        • Connecting Cables to Your IDE CD-ROM Interface Card
          • 1. Locate a vacant 16-bit slot in your system (see Figure 2-13).
            • Figure 2-13: Locating a vacant slot.
          • 2. Remove the metal plate from the slot you have chosen and put the screw aside (see Figure 2-14).
            • Figure 2-14: Removing the metal plate from the slot.
          • 3. Align the IDE CD-ROM interface card’s gold-stripped connector with the expansion slot and gent...
            • Figure 2-15: Inserting the IDE CD-ROM interface card.
          • 4. Secure the interface card to the expansion slot with the screw you removed from the metal plat...
            • Figure 2-16: Fastening the IDE CD-ROM interface card to your system.
          • 1. Connect the data cable to your IDE CD-ROM interface card as shown in Figure 2-17. Make sure yo...
            • Figure 2-17: Connecting the data cable to the interface card.
          • 2. If you have an audio card installed in your system, connect the CD audio cable to the CD Audio...
            • Figure 2-18: Connecting the CD audio cable to the audio card.
          • 3. If you do not have an audio card installed in your system, connect a headphone or powered spea...
          • 4. Slide the drives back into place and fasten them to your system as shown in Figure 2-19.
            • Figure 2-19: Fastening the drives to your system.
          • 5. Switch on your system.
          • 6. Proceed to the section “Installing the Software” in this chapter.
        • Connecting Cables to Your Hard Disk Controller Card
          • 1. If you have not backed up your hard disk, please do so before you proceed. For more informatio...
          • 2. Connect the power and data cables to your hard disk as shown in Figure 2-20. Make sure you ali...
            • Figure 2-20: Connecting data cable to your hard disk.
          • 3. Connect the data cable to your hard disk controller card as shown in Figure 2-21. Make sure yo...
            • Figure 2-21: Connecting data cable to the hard disk controller card.
          • 4. If you have an audio card installed in your system, connect the audio cable to the CD Audio Co...
            • Figure 2-22: Connecting the CD audio cable to the audio card.
          • 5. If you do not have an audio card installed in your system, connect a headphone or powered spea...
          • 6. Slide the drives back into place and fasten them to your system as shown in Figure 2-23.
            • Figure 2-23: Fastening the drives to your system.
          • 7. Switch on your system.
          • 8. Proceed to install the software.
    • Installing the Software
      • 1. Insert the CD-ROM Installation Disk into drive A or B of your computer.
      • 2. Type A:INSTALL (or B:INSTALL) and press <Enter>.
      • 3. Follow the instructions on the screen to complete the installation.
    • Testing the Installation
      • 1. Load an audio CD onto your disc tray.
      • 2. Change to the installed directory.
      • 3. Type TESTCD and press <Enter>.
      • 4. Follow the instructions on the screen.